Poulan
Experienced gardeners share their insights in answering this question :
Go to BECO.com and you can order one.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Other Poulan Chainsaw Carburetor Adjustments
A basic procedure is to start the saw, turn the screw clockwise until the engine begins to stall for lack of fuel, then back the screw off until the engine stalls because it has too much fuel. The ideal setting should be midway between these points.
There should be two screws on the front of the carburetor, which are used to adjust the air and fuel mixture. These often look like flat-head screws, and you can use a screwdriver to turn them, adjusting the amount of fuel and air mixing in the carb.
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a Poulan 2000 chainsaw that I tried to adjust the carberator after using it one afternoon. Then it wouldn’t start at all. How do I set the fuel and air “set screws” properly.
ANSWER : Start with “H” and “L” needle valves 1.5 turns CCW from lightly seated. Then tune for performance like this.
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly. Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.
There are 2 wav (sound – idle & full – may not be highlighted) files that I find most helpful, I think you will too. Good Luck. HTH
Lou
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly. Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.
There are 2 wav (sound – idle & full – may not be highlighted) files that I find most helpful, I think you will too. Good Luck. HTH
Lou
Read Full Q/A … : Poulan
How to adjust carburetor on Poulan FL1500 blower
ANSWER : The L and H mixture screws have unorthodox heads on them, but they can be turned. You can buy a tool for the type of head they have on Ebay. I use a plastic automotive type wire terminal connector and tap it over the head of the mixture screw. The 22 gauge ring-eye type works well because it gives you something to grasp and turn the screw with. Here is the manufacturer’s tutorial on adjusting your carburetor.
http://www.zamacarb.com/tipspage.html
Read Full Q/A … : Poulan
What are the high and low carburetor settings on a poulan 3416 chainsaw?
ANSWER : Are they two separate screws? one for fast, one for slow.for the slow setting, first start the saw then screw until motor runs smooth without chain moving….if to slow the motor will stop….for fast screw….rev motor flat out then adjust so it screams its head off so to speak….it will need all its power for cutting wood so don’t think you are opening it up to much as its designed for it.
Read Full Q/A … : Poulan
Poulan Pro Pruner cuts off when trigger is pulled past halfway; is this car orator issues?
ANSWER : Most likely carb adjustment. Try enrichment adjustment about 1/8 turn at a time, remembering where is was in case you need to go back.
Read Full Q/A … : Poulan
Can you adjust the oil pump – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Depends on the saw. If it is adjustable then it will be adjusted from the bottom of the saw. Most have a diagram on the bottom showing which direction to turn the screw
Read Full Q/A … : Poulan
Adjustment for coil. how many thousands of " – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Most coil to flywheel adjustment is fixed by the mounting screws
it will be around .002″ or have clearance as close to the flywheel without touching it as contact is a dead short
it will be around .002″ or have clearance as close to the flywheel without touching it as contact is a dead short
Read Full Q/A … : Poulan
Carb adjustment for a Poulan Wild thing 2375 – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Start at 1.5 CCW from lightly seated then tune for performance like this:
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly.Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.
There are 2 wav (sound – idle & full – may not be highlighted) files that I find most helpful, I think you will too. HTH
Lou
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly.Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.
There are 2 wav (sound – idle & full – may not be highlighted) files that I find most helpful, I think you will too. HTH
Lou
Read Full Q/A … : Poulan
Changing a primer bulb on a poulan pro chainsaw?
ANSWER : If it is one those that is extrenal to the carburetor you change the whole primer assembly and not just the bulb.
Read Full Q/A … : Poulan
