Husqvarna

The change oil now flashes 13 hours after changing the oil,
how do I reset it?

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Hold the Reset Button and Turn the Key

Turn the ignition back to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.

Every time you get your car`s oil changed, it`s important to reset the oil change indicator light on your dashboard.
What does oil reset mean? Oil reset is the process of resetting the oil change reminder system on the vehicle`s dashboard after an oil change has been performed.
If your oil light stays on even after changing your engine oil, you`re going to want to check the sensor first to rule out a malfunctioning sensor as the cause. Dirt and other particles can make their way into the oil pump, causing the sensor to falsely identify oil issues.
Generally speaking, you have about 2 weeks or 500 miles of driving before a flashing oil light turns into a legitimate problem.
Step 1 – Put your key into the ignition and turn it to the on position without starting the engine. Step 2 – Slowly press the gas pedal three times in a row within 10 seconds. This should reset the system. Step 3 – Verify the reset by turning the ignition off and then on again.
Unlike the car`s gasoline gauge, the oil life indicator should never be interpreted as simply a measurement of the amount of oil in the tank. Instead, it is an indicator of the oil`s ability to properly lubricate the engine, which it can`t do effectively once it becomes overloaded with dirt and other contaminants.
You`ve probably noticed that when you start your engine, your “service oil” indicator will usually light up for a few seconds. This is normal and helps ensure that the bulbs in your dashboard are working properly. But if your light stays on, that`s when you know you`re ready for an oil or filter change.
Your Car Needs an Oil Change

An illuminated check engine light is the first warning sign that your vehicle needs an oil change. It can activate because the oil is too dirty or when there`s not enough flowing throughout the engine.

Do you know how often you need to change the oil in a zero turn? The first oil change should take place after just 5-8 hours of use. However, after that initial change it is recommended to only change it after every 50 hours.
Husqvarna`s Full Synthetic 10W-30 4-Stroke engine oil is a premium oil blend designed for tough, commercial use. Ideal for tractors, commercial zero turn mowers and commercial walk behind mowers. Excellent high temperature protection, and reduced engine wear and scuffing.
Blue or white smoke coming from your engine usually indicates burning oil, which can be caused by: Overfilling the crankcase with oil. Incorrect oil grades. Operating engine at greater than a 15 degree angle.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Husqvarna iz4817 change oil light needs to be reset
ANSWER : The oil change reminder will flash at 49 hrs for 2 hrs then reset itself. It will do this every 50 hrs.

Read Full Q/A … : Husqvarna

How to reset the oil change gauge on the dash after giving an oil change??
ANSWER : From a Husqvarna forum I got that the icon blinks and will stop blinking after a couple of hours of operation (two hours or so).
There is nothing to do or that you can do to stop or reset this blinking.
Gary

Read Full Q/A … : Husqvarna

2700 Series Presser Washer, and I need to change the “engine” oil. There on two oil “yellow” fill point, and the manual talks about changing the pump oil. How exactly do I change the engine oil?
ANSWER : Look for a drain plug on the base of the engine.Take the fill cap off also, and it’ll drain easier.

Read Full Q/A … : Husqvarna

Dont know what type of oil to use – Toro Power Lawn Mower
ANSWER : Put straight 30 weight motor oil in it. Not 10W30 or any multi-viscosity oil. Straight 30 weight motor oil. If you’re doing a complete oil change, then you may want to use Synthetic 30 weight, which will last longer between oil changes and also make your engine last longer (but it costs more too). Best of luck to you.James

Read Full Q/A … : Husqvarna

How do i rest the oil change light – Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348
ANSWER : Hi, it will reset itself after about two hours further use. Regards Phil.

Read Full Q/A … : Husqvarna

How to reset oil change indicator on my husqvarna riding lawn mower
ANSWER : Depends on how old the mower is, for the past 3-4 years, Husqvarna made it so that you have to replace the unit, unable to just reset it.

Read Full Q/A … : Husqvarna

What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.

Read Full Q/A … : Husqvarna

Craftsman ys 4500 lawn tractor change oil indicator won’t go off
ANSWER : Being a reminder light it should reset itself after engine run hours increase from the programed reminder time

Read Full Q/A … : Husqvarna