Poulan/Weed Eater #Wt200 711724 24cc Gas Blower/Vac

Experienced gardeners share their insights in answering this question :
Possible broken cable or gear

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A blocked or dirty fuel filter

You need air for your initial spark – and if oxygen cannot move readily through the system you will have problems both starting and keeping your whipper snipper running. Wash the air filter in soap and hot water, then allow to air-dry.

If your trimmer engine idles, but stalls on throttle, check the following parts: the gasket, primer bulb, fuel filter, air filter, fuel vent, fuel line, and carburetor. The repair and symptom guide will help you better identify the part needed to be replaced and how.
Worn clutch – Since the string trimmer clutch engages with one or more drive shafts attached to the trimmer head to rotate the head when the throttle trigger is depressed, a worn-out clutch may prevent the trimmer head from spinning. A new clutch assembly is relatively inexpensive and easy to install.
If the spool and line on your grass trimmer are fine but your trimmer still isn`t cutting properly, you`ll need to check if the blade on the trimmer`s guard is dull, broken or has come away.
The most likely culprit is a dirty or clogged air filter. Issues with your fuel pump or fuel filter can also cause your engine to idle then die with any throttle. If you have an older car, it could also be a bad carburetor.
If your trimmer won`t turn on, especially if it has not been used recently, you may simply have a drained battery. Plug your trimmer into your charger and see if anything happens. Ideally your trimmer will recognize it has been connected to a power source and charge its battery.
If your 2-stroke brushcutter fails to start, the simplest explanation is that there is not enough fuel: in this case you simply need to top it up. A 2-stroke brushcutter engine runs on fuel/oil mixture, which you can buy ready prepared, such as EFCO-Mix Alkilate alkylated mixture in a 5 L can.
Cable ties as strimmer cord

Have you ever been in the middle of tidying the edges of your lawn when your strimmer cord gives up on you? Cable ties offer a great solution but if your first choice of ties break too, consider using thicker ones.

A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
2. Can I use my phone`s charging cable to charge the trimmer? It can be charged using the USB Type C charging cable included in the package or any standard Type C cable used for charging your smartphone, can be used for charging this trimmer.
At high rates of overcharge a battery will progressively heat up. As it gets hotter it will accept more current, heating up even further. This is called thermal runaway and it can destroy a battery in as little as a few hours.
If the cutting-line head does not stop turning at all, the trimmer will require service at an authorized Honda retailer. The common causes of this problem include an excessive idle speed, a faulty throttle cable, or a clutch that has become excessively worn or damaged due to frequent trimmer use.
Trimmer line does tend to dry out over time and becomes more brittle. Storing it or soaking it in water will help reduce line breakage and make the line more flexible. Be sure to deplete your supply of last year`s line before you purchase new line and begin using it.
If the cutting-line head does not stop turning at all, the trimmer will require service at an authorized Honda retailer. The common causes of this problem include an excessive idle speed, a faulty throttle cable, or a clutch that has become excessively worn or damaged due to frequent trimmer use.
One reason why one of these trimmers may die at full throttle is that too much oil is in the gas, which causes poor combustion. Improper operation, including overuse of the choke, can also be responsible. Poor combustion produces carbon deposits that foul the spark plug and exhaust port, making the problem worse.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My weedeater head sins freely but will not spin when running
ANSWER : Possible broken cable or gear

My Husqvarna 128cd weedeater would run with choke on but not in the run position. Sometimes it would run in the run position but would not stay running. I had it running and then it cut off. I now cannot get it to crank at all. Any ideas
ANSWER : More than likely a fueling issue, wrong fuel air mix or air leak somewhere

How do you take off the spool head of a craftman weedeater and replace it with a precut line head?
ANSWER : You can remove the spool by pulling firmly on the tapper button to remove it. The spool will then be exposed and can be replaced. reinstall the button by snapping back into place.

Hard to start and will only run on choke or partial choke
ANSWER : Hi,The
problem is probably due to a fuel flow problem or clogged air filter, but could be caused by
the insulation of the spark plug breaking down when it gets hot. Try
changing the plug and if this doesn’t work have a look at these tips:http://www.fixya.com/support/r9230929-weed_eater_strimmer_will_not_startHope this helps!

Weed eater starts but won't stay running – Weedeater 19 in 25cc Gas Hedge Trimmer
ANSWER : Probably “gum” and “varnish” build-up clogging the TINY passages [called ‘galleries”] inside the carb!

Shaft disengages and trimmer head stops spinning. Seems to be disengaging at coupling were attachments hook up. Shaft slides back and forth and when I turn trimmer off and jiggle trimmer then start it back up it works for a while then stops.
ANSWER : Something wrong with your cintrifical force clutch . it is problably set too loose so the the shaft wont engage

Removing spool on weedeater SG11 Electic
ANSWER : Pull on the tap head. Straight out. Hard. Here’s the Weedeater manual. http://72.3.225.179/manuals/545117522e.pdf

The spool should just pull out, its held in by 2 clips, royate it till it pops up then pull it out, with a wiggling motion,
Grasp firmly and pull straight out….per tech support from 800 number on machine.

How do i adjust the carburetor high and low mix on a weedeaterblower fb25..
ANSWER : Initial start adjustment is 1 full turn out on both low and high side.