ttle up it seems to smother (for lack of a better word) the carb and it loses power and dies.
Poulan/Weed Eater #Wt200 711724 24cc Gas Blower/Vac

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the engine may not start. To unclog the spark arrestor, remove it and clean it with a wire brush. You may also replace the spark arrestor.
A: The fuel-oil mixture ratio is 40:1. You can obtain this ratio by mixing 3.2 oz. of two cycle air cooled engine oil with one gallon of regular gas.
A: The spark plug gap on all products is . 025-inch.
There may be old or bad fuel in the carburetor float bowl. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and make the engine hard to start. If the carburetor is clogged, try cleaning it with carburetor cleaner.
Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas. For a 40:1 mixture, use 3.2 fluid ounces of oil per gallon of gas.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel will evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Is it straight gas or mixed? – Poulan Pro 14" Gas Chainsaw 33CC P3314
ANSWER : It uses a gas/oil mix. 40:1Hope this helps.

I need the gas mix oil ratio for the Poluan Pro 42…
ANSWER : 40:1 gas to oil ratio.

Do I need gas and oil mix – Poulan Super 250a Chainsaw Plate
ANSWER : I think Poulan uses a 40:1 ratio to one gallon of gas, however I have always used 50:1 the same as my sthl saws with no issue. I would rather have more oil mix that to little.

What kind of oil do i MIX WITH THE FUEL – Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw
ANSWER : 2 STROKE OIL.THE ONE 2 STROKE MOTORCYCLE USE.If you need more help post back!
Thumbs and testimonial are welcome!

How do u mix the 50/1 ratio oil and gas mixture
ANSWER : Mix 2 1/2 oz of 2 cycle oil into 1 gal of gas

I have a Pouan Pro. I can start it but then when I give it gas it seems to have no power. It doesn’t die, just gets no power. Occasionally it revs.
ANSWER : It may well be running too rich because the air filter is blocked, remove the filter and just try the revs again free running, if ok, clean/replace the filter.

Do you mix gas and oil in this trimmer – Ryobi 30 Cubic Centimeter Curved Shaft Gas Trimmer
ANSWER : Yes. Verifythe ratio, either 40:1 or 50:1

Poulan blower was running – ran out of gas – put gas in – won’t start- primed – won’t start – let sit – won’t start-took cover off – sprayed starter fluid in carb – won’t start- -(very little stutter) won’t start-set overnight – repea -twon’t start-wits end !!!
ANSWER : Hello
Does it use a fuel and oil mixture?You probably did that.

Try removing the spark plug and cleaning it with a wire brush or some emery cloth.Make sure you have spark by connecting the plug wire and resting the plug on the metal motor block.

Do not hold the plug in your hand ,if you have no spark you may have a bad magneto.