nk was pieces of hose and the filter. Only one hole coming out of the tank (not two like my other 2 cycle engines). The carb is a Walbro 940 WT324 and has two fuel line nipples… Does it go filter- out the tank – Y to primer bulb – carb and other side of Y straight to carb? Which nipple on carb is for the prime and which is straight from the tank?
Thanks,
Tom
Pro Chain Saw 46cc 20″

Experienced gardeners share their insights in answering this question :
Check out epartsreplacement.com and there is a video on there you can watch that talks about fuel line replacement. It is a very helpful video Tom. Good luck

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
Replacing the fuel hose on your vehicle is going to take time and patience, and it could require getting underneath the car. It`s also going to take the right tools for the job.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My Poulan 2025 Chainsaw fuel hoses have broke down and fell apart. I have new fuel line but do not know the hose routing. All I found in the tank was pieces of hose and the filter. Only one hole coming out of the tank (not two like my other 2 cycle engines). The carb is a Walbro 940 WT324 and has two fuel line nipples… Does it go filter- out the tank – Y to primer bulb – carb and other side of Y straight to carb? Which nipple on carb is for the prime and which is straight from the tank?
Thanks,
Tom
ANSWER : Check out epartsreplacement.com and there is a video on there you can watch that talks about fuel line replacement. It is a very helpful video Tom. Good luck

Read Full Q/A … : Pro Chain Saw 46cc 20″

I have a husqvarna 323L string trimmer. I stored it after running the tank & carb dry for about two years. I fueled it, then started it, & it ran for a minute then died like I turned the switch off. Since it would not restart, I found the fuel filter had broken off the hardened fuel line & it sucked gummy crap out of the tank & into the carb. Failing at cleaning the carb, I finally put a new carb on it & replaced the pump, hoses & filter. It has ran good till this year. I winterized it with stabilizer & left it with a full tank over the winter. The gas in the tank was gone when I got ready to use it this year. I filled the tank with premix, checked for leaks, then started it. It would run fine for about half a tank, start idling poorly (lean) then cutoff & refuse to restart till I refilled the tank. I finally found the tank had cracks & was letting pressure out of the tank & apparently this was causing the carb to lose it’s ability to siphon gas out of the tank. So I replaced the tank which came with new hoses & a filter, which I properly installed to the carb. It cranked right up, but when it runs a half tank, the carb quits sucking gas out of the tank. When I pump to prime the carb, it moves the fuel into the carb, but the pump never gets hard like it does when I prime the carb when the motor is cold. I have to keep refilling the tank, prime, & then it starts & runs until the tank gets about half empty. The new fuel filter is down in the gas tank properly, but It will not run after it shuts off until I refill the tank & prime. I’m baffled. New tank, new hoses, new filter, new carb, & I can find no leaks in the fuel system. It runs strong. The 323L is a two-stroke & it always cranks on the second pull from cold on a full tank. Any ideas?
ANSWER :

Read Full Q/A … : Pro Chain Saw 46cc 20″

Have a craftsman 16″ chain saw 358.360260. Could not initially get it started after it had sat for a couple years with fuel stabilizer in it. When I went to use it the fuel had all evaporated and the fuel pick line was rotted. I replaced that with some difficulty but finally got it on. Saw still wouldn’t start. Replaced the fuel filter. Still wouldn’t start. Pulled the carb apart and cleaned and recleaned everything. Diaphragms were good and I didn’t adjust any of the mixture screws because as I said it ran fine before storage. Non of the carb passages were clogged. Fresh gas 40:1, good spark plug and good spark. Airfilter is good. Engine has maybe about 4 hours of total run time on it. It’s a ZAMA (?) carb. It will run for about 30 seconds when I manually prime it by pouring a small amount of fuel directly though the carb. When I was disassembling the carb the vent hose that goes back into the fuel tank seemed to have a small out of ?substance? in it which I cleaned out. It was right at the end the of the hose that goes back into the fuel tank and not up by the carb. It didn’t appear to be like your typical gummy deposits/varnish though. I hope it wasn?t some type of spongy check valve stuff that is supposed to be in there. That might explain some of my problems. Anyway, I also can not seem to get the primer bulb to fill. When I open the fuel tank, look in side and depress the primer bulb, air bubbles come out of the fuel filter. But when I let the bulb reexpand there’s no fuel that gets sucked up the hose. I can however seem to fill the primer bulb when the fuel tank is full and the chainsaw is laying on it?s pull cord side and the bulb is depressed a bunch of times. The saw will also start and run again for about 15 seconds then die. It’s definitely not getting/fuel and probably running out . Thanks.
ANSWER :

Read Full Q/A … : Pro Chain Saw 46cc 20″

Routing of fuel lines from tank to primer bulb to carb
ANSWER : Line with filter goes to carb inlet,
Line from carb goes to inlet side of bulb.
Line from bulb goes to tank

Read Full Q/A … : Pro Chain Saw 46cc 20″

Which fuel line “port/inlet” on the Walbro wt-380 goes to the fuel tank? It’s on a Craftsman 25cc Gas “Weed Wacker” Line Trimmer purchased in 2002. It has Walbro WT-380 carburetor with external primer bulb. The carb has two inlets for attaching fuel lines – one to gas tank, one to primer bulb. One inlet is on diaphragm side of carb (side with the two Low/High speed adjustment screws). Other inlet is on “reservoir?” side (side with air/fuel mixture screw). Which inlet gets the “fuel tank line”? (Other will obviously go to primer bulb. I found all kinds of diagrams on web but none that showed this. Your assistance is greatly appreciated. (Problem occurs when replacing gas lines and forget which line goes where:)
ANSWER : Usually the line with the filter on it that comes from the tank goes to carb. inlet first which is most likely close to the bottom side of the carb.nearest to the engine,then the outlet or return line on the carb.goes to the inlet side of the primer and the outlet side of the primer goes back to the tank. The primer draws fuel through the carb to the primer to the tank if its not? then correct the line connections until it does

Read Full Q/A … : Pro Chain Saw 46cc 20″

Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up

Read Full Q/A … : Pro Chain Saw 46cc 20″

The saw starts up fine, runs fine but not for long. it runs for about 1 minute and dies. like it is out of fuel or sucking air, i noticed there is no filter on the suction line and there is another nipple entering the fuel tank which appears to need a hose on it , is this just a return line, or should the long line in side the tank press on to this nipple? thanks,
ANSWER : I’ve had my pp4218 for about 2 years and the fuel lines have rotted. I’m thinging from ethanol in the gas. However, I’m replacing them and cannot tell which lines go where. Does the large line from the bubble go to the filter and the little line return?

Read Full Q/A … : Pro Chain Saw 46cc 20″

Poulan te 450 cxl fuel lines need routed correctly two line both in tank one to fuel filter other line?
ANSWER : Other line is just left open like to send gas back from the carb.

Read Full Q/A … : Pro Chain Saw 46cc 20″