Oregon Cutting Systems

Experienced gardeners share their insights in answering this question :
Leave the choke on for longer until it heats up some

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. The result is that too much fuel is delivered to the combustion chamber when the throttle is released, and the engine doesn`t really slow. says Chainsawr.
This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted. Fuel related failures are not warranty.
The carburetor regulates the ratio of air and fuel that enters the engine. If extra air enters the mixture after the carburetor, the ratio will become lean, which will increase the engine RPMs. This air can enter through the gasket on the carburetor if the gasket it loose or damaged.
Safety Switch. Craftsman chainsaws can stop running when they get extremely hot as a precautionary measure. Many models have auto-off settings that prevent the engine from burning out. If an engine does not shut off, it can be damaged beyond repair.
Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised. Cutting a thick wood or timber while running at a low speed or throttle can cause the blades of the chainsaw to become dull.
Information we found online suggests that Stihl Pro Chainsaws have a run time of about 2,000 hours. That means the saw would last you for a minimum of 5.5 years before dying. Keep in mind this time is rated for professional chainsaws and not for regular homeowner saws.
The reason for that may be you`re using the saw at altitude or the carburetor adjustment has simply slipped. The saw also won`t operate well at speed if the air filter or spark arrestor or carburetor are dirty.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mt999 chainsaw. Brand new. Not cutting through wood although blade rotating. Just seems to be burning wood.
ANSWER : Shouldnt be using a chainsaw if you cant figure the chain is on wrong…….just saying…

Read Full Q/A … : Oregon Cutting Systems

Chainsaw starts and idles no trouble but when i try to rev up for cutting the engine dies as if it is not getting fuel
ANSWER : Low side adjustment issue. Turn it out a quarter turn and try it again.

Read Full Q/A … : Oregon Cutting Systems

Saw is cutting the wood on an angle – Stihl 009l
ANSWER : The cutters on your chain are not filed evenly. Either take saw to a Stihl dealer and have chain sharpened or get a new chain. Ask them to show you how to sharpen your chain.

Read Full Q/A … : Oregon Cutting Systems

My stihl keep cutting out if fuel not getting through what can i do
ANSWER : Replace the in-tank fuel filter. Always the easy thing first.

Read Full Q/A … : Oregon Cutting Systems

Can I run an 18in bar on a 16in chain saw
ANSWER : You should be able to without issue.
The Stalling issue started after lengthening the bar/chain?

Read Full Q/A … : Oregon Cutting Systems

Troubleshooting chainsaw hit some dirt now wont cut and smokes at chain little oil to bar and chain
ANSWER : You need to clean the chainsaw areas where the dirt has gone with a water hose. You may have clogged up the oil thing that puts oil on the chain. Hope this helps! And yes, dirt will make a chain dull. You might have to replace the chain or have it sharpened.

Read Full Q/A … : Oregon Cutting Systems

Chain saw starts fine, idles fine, and powers up fine when not cutting a long how when starting to cut a log it bogs down and dies. Does anyone know how to fix this problem or what’s wrong with the chain saw?
ANSWER : Two things that can cause this problem. 1. Your carburetor is not set properly and is not letting the engine get enough fuel under a load. 2. Your chain is binding when you put the chain bar down on the log. Make sure your front chain sproket is turning free and is not too sloppy.

Read Full Q/A … : Oregon Cutting Systems

Won't start – Homelite Consumer Products 9.0 Amp, 14 In. Chainsaw
ANSWER : In my dealings with electric chainsaws if you try to cut wood too big in diameter the electric motor burns out and you will net to replace the saw

Read Full Q/A … : Oregon Cutting Systems