tink it could be anautomatic one
21 In Classic Walk Behind Push Lawn Mower ()
Experienced gardeners share their insights in answering this question :
Hi paul
Here are a few suggestions for you to check
I think it sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line/s condition…after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one.When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.Also a good time to take a picture for later reference for reassembly.
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me Bud
Here are a few suggestions for you to check
I think it sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line/s condition…after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one.When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.Also a good time to take a picture for later reference for reassembly.
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me Bud
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Your Mower Won`t Start:
Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.
Disconnected, dirty or fouled spark plugs are common causes for engines that won`t start. For small engines, spark plugs typically need to be replaced every season or after 25 hours of use. You should also check to make sure the spark plug gap is set correctly.
If the plug is clean or you`ve replaced it and the mower still won`t start, the issue could be a lack of fuel. Either the carburetor is dirty and not able to mist the fuel to be mixed with incoming air, or no gas is getting to it to begin with.
An airlock is one of the common causes why your mower won`t start after running out of fuel. An Airlock occurs when air replaces fuel in the fuel lines. As you refill your fuel tank, you could push the air towards your mower`s carburetor, which keeps the new fuel from reaching the engine.
You Lose Power in the Middle of Mowing:
Here`s why this happens and what you can do: Dirty Air Filter on Your Lawn Mower: Clean or replace. Dirty Spark Plug: Clean or replace. Build Up of Clippings & Debris: Clean underside of your lawn mower deck as noted above.
A Dirty Carburetor Can Cause a Lawnmower To Start Then Die
By far, the most common issue that causes a stalled motor is a dirty carburetor. The carburetor on your engine is the thing that draws in air and mixes it with the fuel. Contrary to what the movies might make you think, gasoline itself is not very flammable.
An engine that will fire and run with the choke closed but dies when the choke is opened likely has debris at least partially blocking the fuel passages in the carburetor. In this condition the closed choke provides enough extra fuel to enter the engine to overcome the lack of fuel flowing through the other passages.
Use Carburetor Cleaner
Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleanerOpens a new window, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.
If your carbureted engine turns or cranks but won`t start, there`s not enough fuel or spark. Here`s what could be causing your engine to crank: Bad crankshaft position sensor. Clogged fuel injectors.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
My mower will only start when i prime the carb and then cut out once dat small bit of fuel is burnt off, its a carb with a float and no choke, tink it could be anautomatic one
ANSWER : Hi paul
Here are a few suggestions for you to check
I think it sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line/s condition…after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one.When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.Also a good time to take a picture for later reference for reassembly.
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me Bud
Here are a few suggestions for you to check
I think it sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper and or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of sharp instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line/s condition…after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one.When you remove your fuel lines from the carburetor be sure to make a drawing or take a picture of how the lines are connected to the carburetor.Also a good time to take a picture for later reference for reassembly.
If the mower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me Bud
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
Lawn mower will start and run for 5 seconds and shut down
ANSWER : Will it stay running with your choke on? if so then clean your carb. if not then look for a blockage from tank to carb. ie fuel shut off, deteriorated fuel line. plugged filter etc
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
I have had a poulan pro 550 series push mower for almost 1 year at the end of the season last year the mower would start briefly and then stop. i have cleaned out the air filter and that did not help.the mower started, i made one revolution around the yard 3/4th of the way the mower quit. I then primed the mower it started then quit and now it will not start at all. Does anyone have any suggestions of what to do. Thanks
ANSWER : There is a little spring that works the carburetor arm. If that popped off then the mower will not run.
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
Wont start no ignition put new plug in and fuel filter
ANSWER : Flush gas tank, fill with fresh gas and Stabil. Replace air filter. Remove bowl from carb clean bowl and holes in bowl screw.
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
Have a craftsman 16″ chain saw 358.360260. Could not initially get it started after it had sat for a couple years with fuel stabilizer in it. When I went to use it the fuel had all evaporated and the fuel pick line was rotted. I replaced that with some difficulty but finally got it on. Saw still wouldn’t start. Replaced the fuel filter. Still wouldn’t start. Pulled the carb apart and cleaned and recleaned everything. Diaphragms were good and I didn’t adjust any of the mixture screws because as I said it ran fine before storage. Non of the carb passages were clogged. Fresh gas 40:1, good spark plug and good spark. Airfilter is good. Engine has maybe about 4 hours of total run time on it. It’s a ZAMA (?) carb. It will run for about 30 seconds when I manually prime it by pouring a small amount of fuel directly though the carb. When I was disassembling the carb the vent hose that goes back into the fuel tank seemed to have a small out of ?substance? in it which I cleaned out. It was right at the end the of the hose that goes back into the fuel tank and not up by the carb. It didn’t appear to be like your typical gummy deposits/varnish though. I hope it wasn?t some type of spongy check valve stuff that is supposed to be in there. That might explain some of my problems. Anyway, I also can not seem to get the primer bulb to fill. When I open the fuel tank, look in side and depress the primer bulb, air bubbles come out of the fuel filter. But when I let the bulb reexpand there’s no fuel that gets sucked up the hose. I can however seem to fill the primer bulb when the fuel tank is full and the chainsaw is laying on it?s pull cord side and the bulb is depressed a bunch of times. The saw will also start and run again for about 15 seconds then die. It’s definitely not getting/fuel and probably running out . Thanks.
ANSWER :
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
Mower start up and runs, but starts to cut back, and smokes just a little bit. The mower stops smoking when it throttle up. It will continue to run but not at full throttle. I can hold a finger gently over the fuel primer bulb and it will throttle up for a small time.
ANSWER : It sounds like she’s being deprived of the correct fuel / air mixture due to a dirty carburetor (the biggest problem with mowers when gas is left to sit for a period of time). If you do not know how to take the carburetor apart and clean it thoroughly, then I suggest taking it to the local shop (hardware store or mower shop) and having it tuned up. It’ll probably be just fine and worth the money. Hope this helps and good luck.James
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
My petrol lwan mower won’t start! I have checked the spark plug and cleaned it, checked the air filter and have also cleaned it they are fine. I have also taken the carburettor to bits and have cleaned it and still no joy. It has a full tank of petrol and the oil is fresh also. I checked the air line and the petrol pipe and these are all ok. When i sprayed quick start into the air filter my lawn mower started up straight away. Then cut out once it had used it up. my throttle plate had also snapped which i fixed and my clutch cable had also come loose which i have tightened and is now fine. The lawn mower is only 3 years old and has not been used for 2 years as my neighbour just went out and brought a new one. so i am trying to get this one started as my electric one has just died on me. I have also been having a go at setting the carb today buy adjusting the air pin but still no joy. It is firing though but just wont start!!! can anyone else suggest anything that might be wrong. Also do these have chokes as i can not find one for it. MY LAWN MOWER IS A POWER DEVIL 3.5HP
ANSWER : When you sprayed the quick start into the thing and it started and ran out, I think the answer sits here you also said you pulled the carb apart to bits it is apparent to me you did not do a thorough job!! Just the fact that you stated that it has not been started for two years tells me that you are having petrol movement problems. For one thing to get started check all the little orifices associated with petrol movement this is surely where you will find your answer to get the machine running, I know this for a fact. You will receive joy just as soon as all your do diligence is finished. If you cannot find the choke on your machine you surely cannot buy one for it. Maybe this repair stuff is just not your thing, maybe as your neighbor before you, you should maybe go shopping and then you will achieve the full amount of joy you are in such desperate need for. Going from electric power to petrol power is a total different world. I think that now my answer to your question is almost as long as your question, so I will be stopping because my fingers are tired of all this typing, GO BLACK HAWKS! Good luck PAL
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
Self propelled mower will start but want stay running long? it runs about 3 or 4 min. then stop and when i restart it, it will start back up.
ANSWER : The fuel bowl has a float and needle, if the float isn’t floating to open the needle for gas to flow into the carb, it will cut off. A kit can be purchased for about $5 or take yours out and soak and clean then replace. Usually when these go bad its best to replace them.
Read Full Q/A … : 21 In Classic Walk Behind Push Lawn Mower ()
