ng exactly the same!
Karcher

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The leak is caused by the filter screen in the clear adapter protruding too far into the threaded section which doesn`t allow a water tight connection on the water inlet. The fix: Make sure the clear adapter is attached to the water inlet and NOT the blue/black adapter. To confirm the clear adapter is the problem.
Here`s how it works, devices from the Home & Garden range can be repaired in our repair centres. Machines within their warranty period are repaired free of charge subject to our Home & Garden terms and conditions.
If the machine is pulsing whilst in use, it may be that the accessory you are using has a blockage. Clear by soaking the accessory in warm soapy water and then rinsing out under the tap.
A: Pretty much everything on the Karcher is repairable.
It Can Harm The Unit

Without water to cool and lubricate it, the pump will work harder than it should, causing it to wear down quickly. This can happen even with just a few seconds of running the pressure washer without the water being turned on. However, the pump is not the only part that takes damage.

Why? This occurs when the Needle Packing Nut is too tight, compressing the Needle Packing too tightly around the Needle. This occurs when the Needle Packing nut is too loose.
Leaking water under the machine

These are often caused by a hole in the water pump or leaky internal washing machine drain hoses. It is better to turn to a professional if the leak occurs regularly despite your efforts. So keep the number of a local washing machine repair man at hand for emergencies.

Leaks when not in use

One is the fill hose at the back, which most people leave under pressure because they don`t turn off the tap when finished. Carefully pull the washer out and see if there is a small drip from anywhere on the hose especially where it screws onto the water valve.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Have a leak where nozzle connects with spray gun
ANSWER : Try useing some teflon tape on the threads.

Read Full Q/A … : Karcher

High pressure hose. How do you get if off the karcher k 3.99
ANSWER : Hi, you have a little black clip in the gun hand where the hose pushes in, just pull it out and the the hose will pullout.

Read Full Q/A … : Karcher

No pressure Pump reassembly. I purchased a new pump and installed it. Got machine back together and I’m not getting any pressure. What would be the signs if I don’t have the shaft key in properly? Or any other suggestions?
Water comes out of nozzle with pressure for a quick second then no pressure, just water. This is a brand new pump so was curious if I installed it wrong. Wondering before taking it apart again.
ANSWER : No pressure would be a sign that the key was not in properly.

Read Full Q/A … : Karcher

Gun leaks I took it apart and replaced the O rings,,, where does the big spring go?? where can I get a repair manual?
ANSWER : Hi, there is a spring in the handle, to enable the trigger; is this what you mean. If so look to see how the trigger works and there is space for this sping to slot into. It can be quite fiddly to get this right!

Read Full Q/A … : Karcher

Unit pressurizes then unloads over and over again with green tip, with red works perectly
ANSWER : Bad green tip

Read Full Q/A … : Karcher

Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.
ANSWER : Bad pump

Read Full Q/A … : Karcher

In the base of a karcher k2,27
ANSWER : Hi,

Diagram attached hope this helps:)

Brad

Read Full Q/A … : Karcher

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in there. I’m thinking it may go over the finger mechanism. I just put it back on top of the finger, like a halo and put the screw in piece back in. Anyway, if you know, let me know how all that goes together.
ANSWER : I fixed mine works good too, watch my video step by step i put it on youtubehttp://www.youtube.com/watch?v=UFXSLOBL0Mg

Read Full Q/A … : Karcher