Black Max 2600 PSI Pressure Washer

Experienced gardeners share their insights in answering this question :
1. Make sure that you are using the black quick connect nozzle supplied with your machine. If you have a vario nozzle (turns back and forth to adjust the spray pattern), you are going to want to pull out on the nozzle to get the machine to a low pressure setting.

2. If you still have an issue, take a paper clip, straighten it out and stick it into the hose nipple on the pump where your chemical hose is connected, push in and out a couple times to free up the ball and spring.

3. If it still doesn’t work, take the chemical nipple assembly apart, make sure there is a o-ring, ball and spring. If one of these are missing you are going to have to order a chemical injector repair kit. If you have all the parts you can streach out the spring a little and put it back together which should make it work.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Inspect the spark plug for signs of wear or damage. If the porcelain insulator is cracked, an electrode is burned away or damaged, or there is heavy carbon buildup at the electrode, replace the spark plug. To determine if the spark plug is defective, use a spark plug tester.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
Each time the power cord is plugged in to an outlet, the Reset button on the GFCI module must be pressed down to connect to electricity. Check to see if the Reset button has been pressed. Next, confirm the small plastic window below the Reset button shows RED in the window.
If you are experiencing this issue, the first thing to check is the sensor area. The sensor area might be obstructed by soap or sanitizer residue. Clean the area, removing any visible residue, and test the unit. Pro Tip: Do not use abrasive cleaners on the dispenser or cartridge.
If you are trying to use your soap dispenser and the trigger stays depressed and doesn`t let you pump the dispenser the spring in the pump mechanism may be jammed. You can unscrew the pump and try to get to the spring. If you cannot get to the spring you will most likely need to replace the pump.
Symptoms of a Failing Check Valve

For example, failing check valves will start to vibrate and even lose some internal parts when problems begin to arise. Other symptoms of check valve failure include reverse flow and excessive component wear and damage. Check valves will also emit noises as they start to break down.

Will an airlock clear itself. Even if you run out of water, air should automatically clear in a well-constructed low-pressure water pipe system. The air should naturally climb to the top and discharge as the pipe system fills up.
Each time the power cord is plugged in to an outlet, the Reset button on the GFCI module must be pressed down to connect to electricity. Check to see if the Reset button has been pressed. Next, confirm the small plastic window below the Reset button shows RED in the window.
You may need to rebuild or replace the pump assembly. If the pump is more than a few years old, and you use the pressure washer fairly often, replace the pump assembly. If the pump is relatively new, and you don`t use the pressure washer often, either rebuild the pump assembly or replace the pump seals.
Each time the power cord is plugged in to an outlet, the Reset button on the GFCI module must be pressed down to connect to electricity. Check to see if the Reset button has been pressed. Next, confirm the small plastic window below the Reset button shows RED in the window.
You may need to rebuild or replace the pump assembly. If the pump is more than a few years old, and you use the pressure washer fairly often, replace the pump assembly. If the pump is relatively new, and you don`t use the pressure washer often, either rebuild the pump assembly or replace the pump seals.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

What kind of soap do I need to use? – Honda Black Max 2600 PSI Pressure Washer
ANSWER : I suppose that would be dependent upon what you would be cleaning eh?If moss on white siding use a bleach solutionOtherwise for general cleaning I prefer “simple green” — you may cut it up to ten times with water….Best regardsCk

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.

Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?

What should I do? Spark Plug? Turn wrenches?

Please let me know

ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.

<!– from fixya rte –>Rope pull start is stuck, won't pull out – Honda Black Max 2600 PSI Pressure Washer
ANSWER : Check the oil level, if it’s very low or burnt then it may have siezed up internally.
It could also be that be that the cylinder is filled with oil or fuel.
if the washer was tipped over the fuel or oil may have migrated in to the piston combustion area.

My Honda PSI 2600 will not suction the solution?
ANSWER : 1. Make sure that you are using the black quick connect nozzle supplied with your machine. If you have a vario nozzle (turns back and forth to adjust the spray pattern), you are going to want to pull out on the nozzle to get the machine to a low pressure setting.

2. If you still have an issue, take a paper clip, straighten it out and stick it into the hose nipple on the pump where your chemical hose is connected, push in and out a couple times to free up the ball and spring.

3. If it still doesn’t work, take the chemical nipple assembly apart, make sure there is a o-ring, ball and spring. If one of these are missing you are going to have to order a chemical injector repair kit. If you have all the parts you can streach out the spring a little and put it back together which should make it work.

I have a excel 2600 psi and there is no spark, the engine is a Honda
ANSWER : Could be many things…get a new spark plug…check plug lead not rubbed and shorting out on body…take flywheel off and check/replace cdi…or points if it has them.

Honda gcv160 wont dispence detergent – Craftsman 2600 PSI Honda Powered Pressure Washer
ANSWER : It will not draw soap while using pressure take out the nozzle or use the large black nozzle

Unloader valve broke off and in need of replacement
ANSWER : Http://www.mastertoolrepair.com/images/020338_0PUMP.pdf

I need to replace the part of the pump where the siphon tube connects. Where can I find the part?
ANSWER : This is for the chemical injector I would try to get it brazzed back on there isn’t a lot of pressure on this fitting And honda olny makes the engine and then depending what kind of pump is on it but likely they olny make the pump So unless you have a part # your olny other recorse is black max and there not realy a top of the industry supplyer of power washers iv’e never deult with the company but i owen and repair this type of equipitment for a business So if you still have the peice that broke off try to fix it i think it will be your best soluition good luck