How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Why would the engine only run while the choke is on or with repeated manual priming? An engine that requires the choking (partial or full) after initial engine warm up is an indication that the engine fuel air mixture system is out of adjustment.
An engine that will fire and run with the choke closed but dies when the choke is opened likely has debris at least partially blocking the fuel passages in the carburetor. In this condition the closed choke provides enough extra fuel to enter the engine to overcome the lack of fuel flowing through the other passages.
Why Does Your Lawn Mower Only Run With Choke On? Your lawn mower only runs with choke on because of a problem with the engine fuel-air mixture system, which can be caused by the carburetor, bad fuel, or air leaks. The choke compels more fuel in the combustion chamber to help the engine to turn over when cold.
If the unit has too much oil, the excess will burn off and create white smoke. NOTE: When first filling the oil level on a new engine or changing the oil on a used engine, keep in mind that there may be a few ounces of residual oil still in the crankcase from factory testing or from when the used oil was drained off.
If your bike is only running with the choke on, it`s probably because it`s running too lean. This can be caused by a few different things: All internal combustion engines need three things to run: fuel, air, and spark. If any of these are missing or not working properly, the engine won`t run.
When does the bike run only with a choke? This mainly happens when there is dirt in and around the parts of the carburetor. The areas of concern here include fuel lines, petcock, pilot jets, or fuel filters. The dirt blocks the fuel passage and it cannot reach the carburetor properly.
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that`s happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
We do not recommend that any type of outdoor power equipment be operated after initial warm-up and with the choke control outside of the normal run position for longer than 5 minutes. Some engines utilize a manual fuel primer bulb to enrich the ratio of fuel in the fuel air mixture for initial engine starting.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Cub cadet 1050 changed oil now its wants me to change oil again and it smokes really bad now to much oil or too little
The 1050 holds 57.5 oz slightly less than 2 qts 64 oz. the filler stick is marked. shiould be over the add mark not over the full mark
Cub Cadet Model SLT1554 PROBLEM: Engine cranks, runs for 1 second then dies. Cranks every time but dies immediately
Sounds like another carburetor blockage. Remove the carburetor and clean out all the orifices in the main jet. Also, check the float for leakage.
PTO will not engage on my 0 turn Cub Cadet RZT 50. What should I check and how do I check it?
See if the switch is getting power to it and if it is see if the clutch is getting power. it needs 12 volts in order to engage.
Cub Cadet zero turn. Cannot get the blades to turn when PTO switch is pulled. Belts are fine and attached. Please help.
I had the same problem. there was a short in the relay just before the wire gets to to back pulley assembly.
Where is the fuse – Cub Cadet LTX 1042 KW 42" 18HP Kawasaki Lawn Tractor – 13WG93AS010
Behind the dash panel at top of dash there is only one fuse
How to speed up reverse – Cub Cadet Op's Manual Model Lt1042 Lt1045 Lt1046 Lt1050
Only way is to change pulley size on pump / has built in gear
When engaging the blades, the mower dies! why? how can we fix it? mower is only one year old.
Get the carburator cleaned there is dirt in it
My z50 cub cadet starts fine but when I release the parking brake it dies. I checked the 20 amp fuse and its good. Pushed in the safety switch on the seat and still dies. What could it be?
There is a safety switch that is attached to your parking brake ander the side board. Check that out.