Garden

Experienced gardeners share their insights in answering this question :
Depending on what it is locked on, but a hammer and big screwdriver, chisel, a couple of hard hits and its off, or there is bolt cutters, or there is a place on the back where you can drill a hole and align the tumblers and unlock it but I don;t remember the actual position, a lock smith would be able to explain it to you

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Door lock problems are often caused by a malfunctioning lock mechanism or latch assembly, but there are several common reasons why locks stop working: The lock is dry or dirty. It doesn`t fit in the door properly. The latch and strike plate don`t align.
Lock is stiff and difficult to open

You can apply some graphite spay or silicone based lubricant in the lock, put the key back in and turn it a few times. Never use oil based products such as WD-40 to lubricate locks because although they may help initially, they tend to cause problems with clogging later on.

A: Unfortunately, you cannot reset this lock without knowing the current combination. You`ll likely need to purchase a new lock.
A: Unfortunately, you cannot reset this lock without knowing the current combination. You`ll likely need to purchase a new lock.
Bumping a Padlock with a Hammer

The simplest way to do this is to insert two fingers into the shackle loop and use them to force the shackle away from the top of the lock. This will put the locking pins inside the lock into the right position for a quick crack-job.

You can visit a Master Lock Distributor / Retailer or submit a Lost Combination form. Bring your lock to the retailer. Be sure that it is not attached to anything. If you do not bring the lock, or it is attached to something, we will not release the combination.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I want to apply scotts grub ex. With an earthway spreader, what setting should i use?
ANSWER : You have scot’s i want bayers grub killer

Read Full Q/A … : Garden

What i s setting on scotts lawn pro spreader to spread lesco momentum force weed andfeed 21-0-11
ANSWER : You can normally gauge it from the size of the granuals i think it is between 6 and 7

Read Full Q/A … : Garden

I have a hand held scotts spreader and i don’t know which setting to put it on.
ANSWER : The setting should be stated on the bag of whatever you are spreading. Use that setting…Good luck…Lee

Read Full Q/A … : Garden

My setting range from 22 to 32… the lime says Scotts should be set on 4&1/2 to 6.
ANSWER : Use Scotts settings for Scotts products.

Read Full Q/A … : Garden

What is spreader setting for scotts southern turf builder on my earthway ev-n.
ANSWER : 3/4 of all the way be sure to shut off before turning as u can clump fert in grass

Read Full Q/A … : Garden

What setting is used to apply 1/4 lb per 100 sq ft?
ANSWER : BigVin, normally the bag of seed tell what setting to put spreader on for its proper application, If not try it on #4 setting, it all depend on how fast you wind and walk with a hand spreader. Good Luck.

Read Full Q/A … : Garden

What are the settings for the zama carb on a 330 homelite chainsaw
ANSWER : 1 1/4 turns out. Then let it warm up and adjust in up to 1/8

Read Full Q/A … : Garden

Need spark plug gap. and carb setting – Mantis 2-Cycle Tiller
ANSWER : Gap should be about .020 – Carb setting is adjusted while running – lo idle and hi – lo idle adjusted to the lowest RPM before it stalls or starts running rough, the hi is adjusted at full throttle for the smoothest / highest rpm

Read Full Q/A … : Garden