Husqvarna
My partner ran over a chainsaw today and now it wont start. We have tried to get it to start but it wont run. Could anyone please help me?
Experienced gardeners share their insights in answering this question :
Check to see if it is getting fuel into the cylinder. Does the sparkplug get wet when trying to start?
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the spark plug produces a spark and you are still having difficulties starting your chainsaw, it`s time to check the gap. The spark plug gap is an air gap between the ground electrode and the center electrode. If the gap is too small, the spark struggles to ignite the fuel and air mixture.
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine. Expect the saw to start on the second or 3rd pull.
With a firm grip (i.e. left hand on top handle and foot through rear handle) pull the starter cord 3–4 times, or until you hear the engine `fire`. NOTE: Do not pull starter cord more the 3–4 times while on full choke to avoid engine flooding.
Smart Start is one of Husqvarna`s unique technology because when their chainsaws are installed with it, it means it`s extremely easy to start.
My chain saw starts and then dies what is wrong? This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted.
If you run a chainsaw without bar oil, it`s likely that the chain will heat up and eventually break. This can cause extensive damage to the chainsaw and may even require a new chain and bar. It`s imperative that you use the correct amount of bar oil.
Many chainsaw models can be started in what is known as `half-throttle` position. In this position, the chain can rotate – if the chain brake is not activated. There are two safe positions to start your chainsaw: on the ground, or with the saw between your legs.
Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine. Expect the saw to start on the second or 3rd pull.
The first is the easiest and most common method. Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions.
Smart Start is one of Husqvarna`s unique technology because when their chainsaws are installed with it, it means it`s extremely easy to start.
What Causes Chain Saw Kickback? There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
With a firm grip (i.e. left hand on top handle and foot through rear handle) pull the starter cord 3–4 times, or until you hear the engine `fire`. NOTE: Do not pull starter cord more the 3–4 times while on full choke to avoid engine flooding.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Poulan 3816, back fires through carburator, wont start.
ANSWER : Water in the gas or carb needs to be removed and taken apart and cleaned
Read Full Q/A … : Husqvarna
Ms170 stihl chainsaw wont start or if it does start it wont take the throttle
ANSWER : Try new gas, and adjust the carb.
Read Full Q/A … : Husqvarna
Dont wont to start to much fuel in cilinder
ANSWER : Never pull the starter more than 3-4 times under full choke. Pull 3-4 times on choke, push in to half choke and pull, should start.
Read Full Q/A … : Husqvarna
Wont start, cant pull the sting. – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : I would recommed removing the muffler and looking into the engine. If you see scoring like this
If the piston is scored it is time for a new machine becauswe the parts and time will be very close to a new unit.
I recommend purchasing a Stihl saw because they last longer.
find a dealer at stihldealer.net
Good luck
Joe
Read Full Q/A … : Husqvarna
Saw will start but dies when rev – Stihl 16" Chainsaw Bar Chain Saw 018 025 Ms 180 250
ANSWER : Check the pick up fuel line in the gas tank. If there is a fuel filter at the end of the line,remove and clean or replace. Use a small fexible wire to hook line and pull out thru gas tank opening.
Read Full Q/A … : Husqvarna
Im having trouble starting my 2 stroke chainsaw. I follow the instructions but it wont fire over it sounds like its just about to but wont.
ANSWER : Here is a Link to one of my Tips:http://www.fixya.com/support/r6081405-cleaning_small_engie_carburetorGood Luck!Jim
Read Full Q/A … : Husqvarna
My rcs5335s engine starts but wont keep running, its starts ok but fizzels out after a few seconds
ANSWER : May have to do carb adjustment
Read Full Q/A … : Husqvarna
Engine runs but wont idle!
ANSWER : Set you carb adjustments at 1 1/4 and try that
Read Full Q/A … : Husqvarna
