mower and it started. now does same thing but won’t start
Experienced gardeners share their insights in answering this question :
Check your battery ad starter connections
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The clicking noise comes from a part called the starter solenoid. The solenoid connects the battery to the starter motor when the solenoid is energized. The key switch and the safety switches in the starter circuit combine to energize the solenoid. If the solenoid is clicking, the circuit that triggers it is working.
Your lawn mower turning over but not starting due to several reasons, such as a faulty or disconnected plug, a disconnected spark plug wire, a clogged air filter, or a contaminated fuel tank. A faulty carburetor, a dirty cutting deck, or a dysfunctional flywheel brake can also cause this.
If the starter motor spins but does not crank the engine, you likely have a problem with… Faulty or damaged battery. To address this issues, check the battery and charging system for problems.
There are several reasons a Craftsman lawnmower may turn over but not start, with the most common ones including the following: Lack of fuel. Dirty air filters. Electrical issues in the ignition system or the starter motor.
Starter motor issues can manifest as a single, loud click emanating from the starter relay or starter solenoid. Usually, this points to a faulty relay or solenoid, or a bad or jammed starter motor.
Worn bearings about to fail completely often make grinding noises, as well as unusual vibrations. The mandrels holding the mower deck`s cutting blades contain two bearings that need frequent lubrication to keep the bearings working properly. As bearings dry and overheat, seals fail and dirt enters the mechanism.
If you just hear a whirring sound like the starter motor is spinning without affecting the motor, then the solenoid is either broken, or there`s a wiring issue on the starter itself. Options are: have the starter rebuilt, replace the whole thing, or see if you can track down the wiring issue on the starter.
Touch the metal shaft of a screwdriver to both of the large terminals at the same time. If the engine turns over and starts, the solenoid is bad and should be replaced. If the starter motor does not run, the motor itself is probably defective.
Signs of a Bad Starter Solenoid
Sometimes, repeatedly trying the ignition can produce a result, but that`s not guaranteed. It usually means there`s a faulty connection in the solenoid. Another common symptom is a single clicking noise when you turn the key.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
My Z5426 won’t start. When I pull out the choke and turn the key, gas starts leaking out of the exhaust system just before it gets to the muffler. Last time it did start, it ran really rough. So, I turn off the engine and then tried to restart and that’s when I noticed the fuel leak.
Maybe bad fuel, fuel line leaking, flooding of the carburetor, since it did start and ran rough I am assuming that the gas was left set and more then likely this gummed up the carburetor, you will have to clean/rebuild it. If you have a can of carburetor clean you may be able to spray that into there and clean it up, I would not choke it to start it as it sounds like it got/is flooded/ing. Good Luck Tim
Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only
My toro 6.5 hp push mower (2010), has no fire to the plug. I have not abused it. i have a small yard and it just gets normal use. Now it won’t fire. I first changed the fuel and cleaned the carb thinking it was that crappy ethanol again. but i grounded out the spark plug and cranked it…no spark. I think it has to do with the lever you pull back to start it . they have some stupid complicated safety contraption that rides along the fly wheel when you pull back on the handle for starting and shutting off the engine. …it looks worn out already…like a mini brake pad. any ideas?…do i really have to replace this garbage every year or am i on the wrong path here?
Unhook your wire from the coil that goes to shut off mechanism, and see if you have spark then. the wire may be grounded out, or your coil might have took a ****
Mower won’t start
This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.
Hope it helps.
I have had a poulan pro 550 series push mower for almost 1 year at the end of the season last year the mower would start briefly and then stop. i have cleaned out the air filter and that did not help.the mower started, i made one revolution around the yard 3/4th of the way the mower quit. I then primed the mower it started then quit and now it will not start at all. Does anyone have any suggestions of what to do. Thanks
There is a little spring that works the carburetor arm. If that popped off then the mower will not run.
Where is the primer ball
It may not have a primer ball. If it does, it would be attached to the carberator. If it starts, but won’t stay running, that could mean your carberator needs to be cleaned/serviced.
My mower will start but won't stay running – Toro LX466 22HP Lawn Tractor 13RT61RH244
I am going to respond 2 times to this post. The first reply will be generic things to check.
First off check the oil level and make sure it is serviced to full.
If your having a lack of fuel (runing lean) you will need to check fuel flow at the carb fuel mainfold. It should fill a spray paint can lid in less than 10 seconds but teting flow rated of the main fuel line. If you have poor flow here… you need to check the fuel filter and the fuel tank outlet port for obstructions.
Good Fuel flow still shutting off…. remove the carb float bow and clean the debris from the bow’ and the treaded area where the fuel solenoid mounts Additionally you will have to again remove the main fuel line and spray carb cleaner in the float needle area to flush out any debris through the fuel hose connection.
For the second response I need to know which engine is installed on your mower by MODEL number if you can locate it. (there are 3 engines) At least try to find the engine model number. If you can not locate it Brand and HP of the engine (I assume 22 hp) Thanks for choosing FixYa,
B&S Quantum Power 4hp won’t start with fresh plug,
Did it run before you changed the plug?Gap is correct, flywheel shear pin may be bad, Water in the Gas?