Husqvarna

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Clearances differ for the two valves and typically range from . 002 – . 004″ to . 005 – .
Valve Clearance Tips

Recommended valve-to-piston clearance is generally 0.080-inch minimum on the intake side and 0.100-inch minimum for the exhaust valve. The exhaust needs a little more clearance because it expands more with heat.

Use a ring spanner to loosen the locknut and turn the screw clockwise to decrease the gap, and the opposite way to increase it. When the clearance is correct, hold the screw with a screwdriver while you tighten the locknut, then re-check the clearance.
To adjust hydraulic lifters two fingers spin the pushrod as the lock nut is gently tightened. When resistance is felt on the pushrod, that`s zero lash. The adjuster is tightened to specs then the setscrew locks it in place. When changing valvetrain components always check rocker arm geometry.
Position the dial indicator on the top of the exhaust-valve retainer and zero the dial indicator. Next depress the exhaust valve. Note the distance traveled. Now subtract the difference in the gasket thicknesses and you should have an accurate measurement of the piston-to-valve clearance.
If your engine generates a loud clatter, it could be time for a valve clearance adjustment, though a tapping noise could also be caused by a loose rocker arm or some other component; the mechanic won`t know for sure without inspecting the valves.
When do I need to have a valve adjustment? You should have your valve lash inspected at manufacturers recommended intervals. A sure sign that it`s time for a valve lash adjustment is if your engine is making a loud clicking or tapping noise when starting up or if you experience a loss in engine power.
Rule of nine

With any given valve open, count what number valve that is from the front. Subtract that number from nine. Whatever number you`re left with is the valve you`re in position to set. So, with number 1 rocker opening its valve, you`ll be setting clearance on (9 minus 1), number 8 valve.

When do I need to have a valve adjustment? You should have your valve lash inspected at manufacturers recommended intervals. A sure sign that it`s time for a valve lash adjustment is if your engine is making a loud clicking or tapping noise when starting up or if you experience a loss in engine power.
In most cases as the valve seat and valve head wear they start to pocket into the head, This reduces the clearances ,if the clearance is reduced to nothing the valve is held open slightly,this reduces the compression of the engine and in turn it will be hard to start .
In most cases as the valve seat and valve head wear they start to pocket into the head, This reduces the clearances ,if the clearance is reduced to nothing the valve is held open slightly,this reduces the compression of the engine and in turn it will be hard to start .

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need to know what the carb adjustments are for a model 61 husky
ANSWER : Low side one turn out from bottem.high sie is the same.after saw is running readjust both high and low.make sure the side dosen’t go in any more then 3/4 of a turn out……if it does you will burn up the saw….

Read Full Q/A … : Husqvarna

What years did husqvarna make model 61 – Husqvarna Chain Saw 20" Bar
ANSWER : Late 70’s into the early 80’s.

Read Full Q/A … : Husqvarna

What information can you tell me about a Husqvarna chainsaw model 61 with serial number 6136460. Does it indicate the year?
ANSWER : Most of the CDI modules have been superseded to part no# 544018401check with your local dealer to verify.

Read Full Q/A … : Husqvarna

Valve clearances for jd la valve adjustment only John Deere Tractor Model L A doesn’t cut it with this web site so that is the reason for this approach
ANSWER : 0.08mm-0.13 mm- intake top
0.13mm-0.18mm- exhaust bottom

Read Full Q/A … : Husqvarna

Colk start trigger isi'nt working – Husqvarna Models 61-66, 266, 268, 272
ANSWER : More details needed. how not working

Read Full Q/A … : Husqvarna

Can chain oiler on husqvarna be adjusted as the oil is just flowing through
ANSWER : You can not adjust the oil pump it helps to use the right oil

Read Full Q/A … : Husqvarna

Setting hi lo on 235 husqvarna – Husqvarna , No.455 Rancher, 20" Gas – Powered Chainsaw
ANSWER : You need a special tool to adjust the mixture screws, i have to say they are not easy to tune, you will also need a rev counter to set the high revs, it is very difficult to give basic settings for the carb as they vary greatly

Read Full Q/A … : Husqvarna

Husqvarna yth20S42 partial loss of drive power can tran oil be checked. The tractor has 170hrs operating time.How can you tell if its the belt or the trans. thanx Rod.
ANSWER : I would thing its the belt I have same mower u can check rear end by removing a check plug also sure that u can adjust the belt try that 1st

Read Full Q/A … : Husqvarna