McCulloch

Mac 3200

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Turn the idle screw — I — clockwise until the chain starts to spin, then turn it counterclockwise slightly. Adjust the screw to find the highest setting possible without making the chain spin. Check the setting by holding a digital tachometer over the spark plug. It should read between 2,700 and 2,900 rpm.
Turn the McCulloch chainsaw upside down, and locate the serial number plate, which is a metal plate on the bottom of the chainsaw. Scan the plate for the word “Model” followed by a series of letters and numbers; the letters and numbers are the model of the chainsaw. A model number example is “CS 380.”
McCulloch Today

In 1999 McCulloch sold its European division to Husqvarna AB. Nine years later, Husqvarna also acquired the rights to the McCulloch brand on the North American market. Since then, McCulloch is a brand within the Husqvarna Group.

The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
The McCulloch CS 35 16 is powered by a 1.4 kW (1.9 HP) two-stroke engine 35 cc.
For products with two-stroke engines, the petrol must be mixed with two-stroke oil. McCulloch recommends “Universal powered by McCulloch two-stroke oil”. The petrol/oil ratio must be 50:1.
To answer the question for those who are short on time, the easy answer is a resounding yes. Yes, you can use a chainsaw to cut wet wood.
In 1999 McCulloch sold its European division to Husqvarna AB. Nine years later, Husqvarna also acquired the rights to the McCulloch brand on the North American market. Since then, McCulloch is a brand within the Husqvarna Group.
Main features. This chainsaw is powered by a 1.5 kW (2.01 HP) two-stroke engine 42 cc.
For most projects, you`ll want a chainsaw that extends approximately 2-4 inches beyond what it is you`ll be cutting. For example, if you`re cutting a tree trunk that is approximately 12 inches wide, a 14″ or 16″ chainsaw would be ideal.
Most modern chainsaws, string trimmers, leaf blowers and other small-engine two-stroke equipment recommend a 50:1 oil mix ratio, but some recommend 40:1 and older two-stroke equipment might even call for 32:1.
The fuel and oil mixture should always be 2% (50:1).
Adjusting the L screw clockwise can cause the chain to engage while the saw is idling. Adjusting the H screw clockwise increases the maximum speed of the engine and can cause damage to your saw`s engine if its operating capacity is exceeded.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need to locate chain & bar oiler adjustment screw for mac 3200 chain saw
ANSWER : Look to the lower left side of the bar (as you hold the saw normally)–there should be a screw head in the engine case there. Check the adjustment by holding the bar tip at speed near a piece of cardboard for a couple of moments–it should throw off a thin line of oil. Hope this helps!

Read Full Q/A … : McCulloch

Want to purchase bolt to adjust the chain on my
mac 3200 Chainsaw
ANSWER : You local Mower Shop should be able to help you, he can order one for you

Read Full Q/A … : McCulloch

I need to know which oil type goes into the oil chamber for the chain on a mac 3200 gas chainsaw, not the mixture…thanks
ANSWER : There really is no exact type of oil that goes into the chain and bar oiler. Each manufacturer usually makes their own, but any chain and bar oil will work. It is a thicker type of oil unlike a motor oil. Just ensure that the bottle says “bar and chain” oil

Read Full Q/A … : McCulloch

My titan 70 also has a oil leak when it is left sitting what would be my problem
ANSWER : The bar oiler can leak oil. Make sure the cap is on good.

Read Full Q/A … : McCulloch

McCullough chainsaw won't start – McCulloch Quality Mcc1435a 14" Gas 35cc 2 Cycle Chainsaw Full Warranty
ANSWER : If it’s a old saw..The seal goes out on the crank next to the clutch,it’s called a grease seal, it loses the suction needed to pull fuel in to the engine, can be a tricky one to replace, but will spark a old saw back to life. You may want to replace both crankshaft seals ..First try a few drops of gas down the carb, if it pops off you know it’s a fuel issue

Read Full Q/A … : McCulloch

I have a mac 3516 with a weak spark.I am looking for the gap spec
for the pickup coil.
ANSWER : The gap should be 0.5mm

Read Full Q/A … : McCulloch

Just purchased a McCulloch 250CXL but the operating manual provided does not contain english instructions.Received machine today 3rd Nov
ANSWER : Goto http://lawnandgarden.manualsonline.com/manuals/mfg/mcculloch/mcculloch_chainsaw_product_list.html

Read Full Q/A … : McCulloch

How to replace a oiler on a stihl chainsaw ? – Stihl Service Manual for 031AV Chainsaw with Parts List
ANSWER : Remove the worm, sealing ring and washer, loosen the pan head screws on the oil pump and replace. Check if the gasket is re-usable.

Read Full Q/A … : McCulloch