McCulloch

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Water leaking from a loose connection can cause the unit to cycle on and off. Verify if the pressure hose has an O-ring at the connection. If missing, this will also cause the unit to cycle on and off. While the unit is running look for any water leaks that may cause the unit to turn back on.
If the pressure washer does not start, then the first thing to check is the fuse in the plug. The reading you`re looking for is the same as it would be when connecting the two probes of the multimeter together (as you can see in the example of this video, this fuse is actually fine).
These include a clogged nozzle, a blocked inlet water filter, or a malfunctioning pump. It could even be the water supply itself – not the pressure washer. When troubleshooting pressure washers, the best approach is to check the easiest solution first and rule it out before proceeding to more intensive repairs.
The fuse is inside the plug… may have to remove both covers.. However, if you get a red light, it is not the fuse, and the plug can go bad if water gets in, in which case you may have to replace it..
A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
There could be small leaks, holes, or tears in your garden hose or high-pressure hose that are causing your pressure washer to lose pressure when you pull the trigger. If you find leaks, plug the holes or replace the hose, which should solve your pressure issues.
It depends on the pressure washing equipment you purchase. New pressure washers will be rated with a number of hours they should last. For example, if it is rated 500 hours and you use it fewer than 50 hours throughout the year then it will last you more than ten years as long as you keep it well maintained.
A washing machine not draining can have multiple causes, including a clogged or jammed drain hose or a broken pump, lid switch, or belt. No matter the culprit, you need to drain the water from the washing machine before diagnosing the issue or doing any work to remedy the situation.
Unplug your washer and wait at least two minutes before plugging it back in. If your model has a manual control panel, turn the knob to any setting other than the final spin. Plug the unit back in and restore power to your laundry room. Your washer should turn on and you should be able to use it again.
Inspect the Motor and Motor Capacitor

A faulty motor capacitor or faulty motor can cause your Whirlpool washing machine not to turn on. The motor capacitor is responsible for providing the necessary starting torque for the motor to run. For either of these issues, you will likely need a professional`s help.

No matter how powerful your pressure washer might be, it`s never a good idea to leave your machine running for too long because doing so will increase the risk that it will overheat. Instead, most professionals suggest using a pressure washer in intervals of three to five minutes.
If the water pressure is too high, it can cause the machine to overheat. Adjust the pressure accordingly and see if that solves the problem. Next, take a look at the machine itself. If there is a build-up of dirt and debris, this can also lead to overheating.
There are also a number of symptoms that will tell you if the capacitor on a motor is faulty: The motor will not start its load, but if you spin the load by hand, the motor will run properly. On air-handling equipment, the motor may start but will always fall short of normal operating speed.
The pressure washer hose will fill with water, so it is important to purge the system of excess air before starting the unit. Simply squeeze the trigger on the gun and the air will release.
Pressure washer pumps, including electric models, use Non-Detergent (ND) oil and most don`t require maintenance. In this post, you`ll learn how to check and add pressure washer engine oil.
Washing Machine Lifespan

The average life of a washing machine ranges from 10 to 13 years, although some brands can manufacture washing machines with an even longer lifespan than the average appliance.

That being said, it`s still possible to find good washing machines that have been built to manage thousands of loads – which, depending on usage levels, can last as long as 20 or 30 years. But today`s cheaper models can often only manage hundreds of loads before buckling under the pressure.
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Load Imbalance

The machine will automatically shut down when it senses the load is out of balance to prevent mechanical damage. Turn the washer off and re-balance the load by moving the clothes to an equal distribution. When you close the lid, spinning should resume.

Washer or Dryer Won`t Start

Go to your home`s main electrical panel and locate the circuit breaker that controls your washer and dryer. If it`s tripped, reset it and try to start the unit again. If the breaker isn`t tripped, then the problem may be with the electrical outlet the unit is plugged into.

If your pressure washer is refusing to work or even turn on, the culprit could potentially be the power switches. Most pressure washers use two micro switches that disconnect both the live and neutral connections between the supply and the motor. These switches can jam cutting the power out from reaching the motor.
There are 2 fuses for the wiper/washer system. If your windshield wipers work, then they are both good. One fuse is located in the under-hood fuse block (wiper fuse #14 , 25amp). The second fuse is located on the body control module, which is located inside the center console, behind the panel on the right side of it.
Washing machines often have a fuse that controls power to the working parts of the machine. Before you attempt to replace this component, you should first unplug your washer. Then, remove the necessary screws to access the machine`s fuse panel.
1. After the washing cycle is complete and washing is done, power down the machine and cut off the water supply. 2. Take out the washed clothes, in the case of a top-loading machine, and turn the knob from “wash” to “drain”.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do i hook up a hose to the power washer – McCulloch FHH18A Electric Pressure Washer
ANSWER : Have you tried looking on the back of the machine?

Read Full Q/A … : McCulloch

MY 1850 PSI POWER WASHER WON’T START UP. As fast as the motor started, it shut down. And there is still power. What is the problem?
ANSWER : Probably a clogged carb from sitting all winter with fuel it it.

Read Full Q/A … : McCulloch

My power washer does not let the soap come out when you turn the soap control on
ANSWER : You have to use the SOAP nozzle (Black Tip)  It is a low pressure nozzle.  The venturi effect prevents the psiphon under high pressure

Read Full Q/A … : McCulloch

Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start

Read Full Q/A … : McCulloch

Power washer won't start – Briggs & Stratton Power Products 1539 Pressure Washer
ANSWER : Have you checked for spark? You can remove the plug, touch it against the block and crank it and see if you have any spark (best done in as dark a place as possible). If you don’t have spark, start by replacing the plug.

If you have spark, you can spray some starter fluid or gas into the cylinder, replace the plug and try to start it. If it runs for a few second, then you have fuel flow problem (dirty carb or filter, etc.).

Hope these basic tips get you going in the right direction.

Read Full Q/A … : McCulloch

Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only

Read Full Q/A … : McCulloch

I have used the McCulloch (FH180A) three times over the course of two years. On my fourth use the pressure washer just surged on and off and I would get a tiny spray from the gun each time it surged. In other words it would do nothing. Please help… very frustrated. Thanks
ANSWER : Sounds like the problem could be low input water flow or pressure. There could be crud on the intake where you hook up the garden hose, there could be some other sort of blockage. Try hooking it up to the hose and pull the trigger (with the power switched off) and wait to see if water comes out the tip. Also look at the tip(s) themselves. sometimes a piece of crud gets into the hose and then clogs the tip.

Read Full Q/A … : McCulloch

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.

Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?

What should I do? Spark Plug? Turn wrenches?

Please let me know

ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.

Read Full Q/A … : McCulloch