Hi i need a manual for scorpion spw-2 pressure washer?
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Clogged carburetors or air filters can cause a pressure washer not to start. If your pressure washer won`t start, you can also check for a clogged carburetor or air filter.
Pressure Washer Nozzles
0 degrees (red nozzle) is the most powerful, concentrated nozzle setting. 15 degrees (yellow nozzle) is used for heavy-duty cleaning. 25 degrees (green nozzle) is used for general cleaning. 40 degrees (white nozzle) is used for vehicles, patio furniture, boats and easily damaged surfaces.
Running a pressure washer without water can cause irreparable damage, sometimes instantly, sometimes gradually over time. Either way, you are better off not risking rendering your machine unusable.
Each time the power cord is plugged in to an outlet, the Reset button on the GFCI module must be pressed down to connect to electricity. Check to see if the Reset button has been pressed. Next, confirm the small plastic window below the Reset button shows RED in the window.
There are a variety of reasons as to why your pressure washer may not start. Some of these include, a dirty air filter, lack of or old fuel, problems with the spark plug wire`s connection or a bad spark plug, water in the fuel or an excessively rich fuel mixture, or the choke is in the ON position.
These include an incoming power problem, a damaged power cord, a malfunctioning door lid switch or lock, a defective user control board or timer, a broken drive belt, or a faulty or obstructed drain pump.
Connect and Turn On the Pressure Washer
Connect the high-pressure hose to the pressure washer, then turn on the pressure washer and set it to the lowest power setting. Make sure that the nozzle is pointed away from you in the direction of the target surface. Grip the wand and pull the trigger to start spraying.
As long as the pressure washer has an inlet hose that`s compatible with the water tank`s outlet, you`ll be able to use it. While being convenient, a water tank also ensures that you have a flow of water that`s constantly running through the pressure washer, therefore preventing it from getting damaged.
The heart of every pressure washer is its electric motor, which drives the pump system . In order for the pumps to work correctly, they need water, which is provided, for example, by a garden hose .
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.
Need help in getting Honda engine on NorthStar pressure washer to run.
Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works
My Honda pressure washer is leaking out of the thermal relief valve and I am looking for a part,I also do not have the manual. The model number is WGC 3030 and it is 3.0 gpm 9.0HP. The number on the thermal valve is 33120004,where can I find a part?
Does the thermal valve just screw into the pump head, if so what size thread is it? I have 1/4, 3/8, 1/2 in stock.
Oil appears to have come out of the oil filler cap. Is this a sign of overfilling the oil, or something else?
Id definitley say its over filled. try checking the dipstick
Honda powwer boss 3000-whenyoupull the handale to spray it kills the engine
Sounds like the unloader (regulator). Try removing the nozzle, the pull the trigger with the engine running. If motor is still running then it could be the Unloader malfunctioning. If you require a new one try a bypass system for the unloader. The bypass will help save the life of the unloader.
Manual Is there anywhere to purchase a manual for my Karchar
Go to karcher.com They have downloadable manuals in .pdf format.
Kranzle electric washer will not suck up soap
Hi, if it has a chemical injector on the machine then the pressure at the lance will have to be lowered for it to pull in soap. it works on a similar principle to how carburetors on cars pull in fuel, bernouli principle. high pressure at one side of an orifice going to low pressure at the other side which causes a negative pressure ( vacuum) which should pull in the soap. there should be a non return valve at the orifice (hole) which prevents the water back feeding into the soap container, it is quite common for this valve to get stuck, it is just a ball, spring and o ring , and the ball sticks to the o ring. if it is this system then take the soap pick up pipe off the injector and just push the ball off it’s seat with a bit of wire.If it is a high pressure soap system then that is different, but they usually work with an injector in my experience.try taking the high pressure hose off the front off the machine and running it, if it has an injector on it it should pull in plenty off soap.hope this helps ,andy
I need a owners manual for a pressure wahser GCV 160 from honda
MiTM will have that. See mitm.com Honda makes the motor but not the pressure washer. Honda does have manuals if you need one for that GCV160 motor.