Craftsman

Experienced gardeners share their insights in answering this question :
Remember this,there is a belt diagram under the left foot rest. It will show you how the belt is rigged onto the pulleys. In changing this belt you will have to pull the clutch assembly,from beneath the motor. Only one bolt holds this assembly to the motor’s vertical shaft.Once removed,install the belt onto the pulleys. Then slip the belt onto the clutch assembly’s pulley and lift straight up,align the key way with the key and slip on the clutch assembly and replace the bolt.Torque down the bolt,i can’t remember the torque pounds,but i believe it’s 100-200 lbs. of torque.B. Locke

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Since you`ll likely only replace your serpentine belt once during the life of your car, it`s generally recommended to take your car to a professional mechanic. You can do a lot of damage to your vehicle if you drive on the road with an improperly installed serpentine belt.
Usually there are two belts. One goes around two pulleys, a front pulley under the motor and one on the mower deck.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
Serpentine belt replacement is easy because today`s automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need a diagram for craftsman 44″ riding mower drive belt. Mine threw belt and cannot locate original manual.
ANSWER : If you can find the model number of your mower, you should be able to find your manual here. I hope this helps.http://www.searspartsdirect.com/partsdirect/index.action

Read Full Q/A … : Craftsman

ROUTING OF BELT – Mtd Drive Belt 42"
ANSWER : Diagram is on the mowing deckBest regardsCk

Read Full Q/A … : Craftsman

Belt diagram for a Craftsman 42″ riding lawn mower
ANSWER : There are as many belt diagrams as there are mowers. You will need your model number to get the correct diagram. You should find this under the seat or on the very back of the unit. sorry can’t help more at this time, when you get this, you can get online and go to sears and you will find it there.

Read Full Q/A … : Craftsman

Craftsman 42 inch belt diagram
ANSWER : Look on deck or under foot pedal there is usually a diagram in those places

Read Full Q/A … : Craftsman

Diagram for belt replacement on 1988 Toyota Tercel
ANSWER : Fig. 1: Correct timing mark placement on 3E and 3E-E enginesHope this helps; also keep in mind that your
feedback is important and I`ll appreciate your time and consideration if
you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Read Full Q/A … : Craftsman

Drive belt popped off by limb i ran over need drive belt diagram
ANSWER : I’ve got a manual. Can I fax to you copy of diagram? Send your info to my fax no. 209-394-0868.

Read Full Q/A … : Craftsman

How to fit new belt – Craftsman 20 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Ya gotta have model numbers. Go to searspartsdirect.com and enter your model number. Most models then have manuals available over on the right hand side of page. Most manuals have pictures or diagrams on bets.

Read Full Q/A … : Craftsman

Need to replace drive belt.Never replaced. 42′ Craftsman riding lawn mower. How difficult is this. How do you access rear drive pully
ANSWER : Take a look at how the belt is installed. Then you will have to remove the mower deck and belt from the pulley on the engine. There is probably something by the engine pulley that you will have to remove so the belt will come off. It might be a shoulder bold or a rod with a bolt holding it on. Same with the rear pulley. Then you just have to put the belt on one pulley and watch your fingers so you don’t pinch them and turn the other pulley and the belt should go on. reinstall any bolts you removed and install the deck.

Read Full Q/A … : Craftsman