ooking for someone to guide me on how to adjust the high and low idle screws to the proper adjustment so it will run.
Tiller

Experienced gardeners share their insights in answering this question :
Check the fuek lines for hole and leaks, check the fuel filter and clean if necessary. remove the carbuerator and inspect the gasket; it should be soft and flexible, if it seems hard or brittle replace it. clean the carb with carb cleaner sray (available at any local auto parts store) and compressed air. make sure you get inside the small fuel rail holes. check the primer bulb for pin holes and seating/sealed properly. if that doesn’t work have the carb repaired at a service center or replaced.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If the rotary tiller still doesn`t start:

Check that the fuel tank isn`t empty: if necessary, add fuel. The fuel must be fresh, of good quality and clean: make sure that no dirt, water or incompatible fuel (such as petrol-oil mixture, if the engine is a 4-stroke) gets into the tank.

One of the most common problems, especially because rototillers often sit unused for months, is stale fuel or a clogged carburetor. If you know you have fresh fuel, you can check for carburetor blockage by spraying a small amount of carb cleaner into the intake and attempting to start the engine.
If there is no spark, this indicates that the spark plug is defective and should be replaced.
IMPORTANT NOTE: Using an undersized cord, a larger number cord gauge (AWG) than recommended in the chart, will cause a loss in power and overheating of the tiller.
If the wheels on your tiller move but the tines don`t spin, you may need to replace tine shaft clevis pins or replace the transmission. The tiller`s transmission drives the wheels and the tine shaft, so you`ll likely need to replace the transmission when the wheels spin but the tine shaft doesn`t move.
You should change your tiller oil at least every spring, but ideally after every 50 hours of operation. Between oil changes, check your oil level before each use to ensure there`s enough oil present. Small amounts of oil may burn off during use, so you may need to occasionally top it off.
1. Do not use the BCS in rain and wet or muddy soil. This is harmful to soil structure, can get the machine stuck in soil, and lead to rusting of machine parts. 2.
Tiller Maintenance

One of the most important things you can do for your tiller is to keep it clean. Wash the tiller, particularly the tines and housing, after each use (be careful not to spray water on a hot engine!). For continued effectiveness, you will need to replace the tines when they become worn down.

Once the fuel tank is empty, push the primer bulb on your tiller 7 or 8 times to clear out any fuel in the carburetor.
How Do I Know If My Praying Mantis Is Hungry? A praying mantis will usually let you know when it is hungry by becoming more active and trying to climb higher up on its cage. You may also see it extend its abdomen and mouthparts as if it is trying to reach for food.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mantis Tiller My Mantis Tiller will not start. It was at least starting before but would not stay running. Now it will not start at all. I am looking for someone to guide me on how to adjust the high and low idle screws to the proper adjustment so it will run.
ANSWER : Check the fuek lines for hole and leaks, check the fuel filter and clean if necessary. remove the carbuerator and inspect the gasket; it should be soft and flexible, if it seems hard or brittle replace it. clean the carb with carb cleaner sray (available at any local auto parts store) and compressed air. make sure you get inside the small fuel rail holes. check the primer bulb for pin holes and seating/sealed properly. if that doesn’t work have the carb repaired at a service center or replaced.

Read Full Q/A … : Tiller

Mantis tiller 7222e
ANSWER : Hi anon, if it’s starting your 2/3rds of the way there. You have fuel and spark. Try and clean the air filter first and if that fails to keep it running then check that the choke isn’t staying out. If all thats ok then it may be the carb gaskets.

Read Full Q/A … : Tiller

Mantis tiller idle screw adjustment – Mantis 2-Cycle Tiller
ANSWER : Start out with 1.5 turns on High speed jdet and 1/2 turn on the low speed. Make sure plug is not wet, better yet install a new one. Clean, fresh fuel and give it a pull.

Read Full Q/A … : Tiller

Will only start and run in choked position, when throttle applied chokes out. If started with out choke and throttle position in low speed will start and run for 10 sec then like it runs out of gas.
ANSWER : I have your solution guaranteed, I fixed mine yesturday remove H L screw plastic caps and on high 11 threads exposed and on the low side 8 threads exposed. removing the plastic caps allows u further adjusting these wear out or move soo just take them things off and you will be rolling

Read Full Q/A … : Tiller

Engin runs fine at idle but stalls out at high idle and wont rev up.
ANSWER : Hi 5flash… Get an assistant and a can of starter fluid. Remove the air cleaner and spray some starter fluid into the air intake. Start it up and spray the starter fluid as you move it to high idle, repeat until it works properly. Joe

Thanks for choosing Fixya!

Read Full Q/A … : Tiller

I have a two cylinder Mantis tiller. It has locked up and the cord is locked. I am unable to pull the cord. Any suggestions? I was in the process of using the tiller when it felt as if it were running out of gas. It stopped on its own, and then it was locked up and I was unable to pull the cord.
ANSWER : Check the oil, if not full fill it, take the shroud off, should be for bolts, fit a socket on it with a breaker bar or ratchet and turn it a few times, then reassemble and start. Hope this helped Tim

Read Full Q/A … : Tiller

Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.

Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.

Then watch this video and do it:

http://www.alamia.us/mantis_parts_s/148.htm

Read Full Q/A … : Tiller

Tines continue to work with out touching safety or throttle. they engage as soon as I start the engine.
ANSWER : Remove H (high) L (low) plastic caps to allow you to further adjust the flow and you will be going. H (red) further out about 11 threads exposed and L (low) about 8 exposed; adjusting the low side will stop the tines, but remove tines before making any adjustments, thanks

Read Full Q/A … : Tiller