Troy-Bilt

I got a troy bilt horse tiller. It was originally purchased about 10 years ago. It was used a couple times and then left to sit in a garage. I got it out and it started right up. I tilled a garden and cleaned it up. I put it into my garage and The next day I notice oil on the floor. I see that transmission oil is leaking around the tines. What needs to me done to repair it? The Thing looks new.
Experienced gardeners share their insights in answering this question :
 an new oil seal needs to be put onto the output shaft of the transmission.  remove the plug wire if you attempt to pry out the old seal and tap in the new seal.  Be careful not to damage the case and grease the seal and shaft when you replace the oil seal 

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Oil can come out of the exhaust of your lawn mower when it is tilted to the extreme, especially when the crankcase is overfilled with oil. A clogged air-filter can cause the oil to spill out of the exhaust vent, so simply replace it if this is the case.
Most commonly, this happens when the oil pan gasket or valve cover gasket are over-tightened. It can also happen when tightness is not evenly distributed. Another reason can be the improper attachment of the oil filter, as the engine oil flows continuously through it, and if it`s loose, you can experience a leak there.
cause: 1) The float contacts with the float chamber wall by gasoline for a long time; 2) The gap between the float pin and the body float pin hole expands after long-term friction, resulting in the contact of the float with the float chamber wall.
Also known as lip seals, shaft seals are mechanical devices that are designed to protect against leakage around a rotating shaft.
An oil leak may be caused by metal chip debris lodged between the head gasket and the block, chip debris between the cylinder head and the head gasket, or by damage to the cylinder head sealing surface that occurred during the manufacturing process.
Engine oil leaks occur most often at the valve cover and oil pan gaskets, timing chain cover and the front and rear crankshaft seals. As an engine ages, heat can cause cork gaskets to harden and shrink. Heat can also cause rubber (neoprene) gaskets and seals to harden and lose elasticity.
Engine oil leaks are one of the most common causes of engine damage. They cause rapid deterioration of the engine and result in expensive repairs. Worse yet, engine oil leaks pose a safety threat. They may lead to the loss of control of the vehicle while driving.
Cracked Gasket: The Core Culprit in Most Engine Oil Leaks

More often than not, a sudden oil leak after oil change is caused by a malformed or cracked gasket. Gaskets are usually made of urethane or rubber, and they can harden over time.

The gasket is probably the most common cause of oil leaks, especially in older vehicles or vehicles that are used frequently & have a high number of miles. The gasket is a seal that joins the head two metal parts of the engine, such as the between the block and the head(s) as well as the engine block and the oil pan.
If your car is burning oil, it`s probably wearing out. Over time, the piston rings have likely become worn or stuck in their grooves, preventing them from sealing tightly against the cylinder wall. The tiny gap that has formed between the ring and cylinder wall allows oil to enter the combustion chamber and burn.
One of the more common questions we get concerns either the overwhelming smell of gas coming from the carburetor or fuel leaking out of the bowl or overflow. Both conditions are typically caused by a stuck or worn float needle valve.
Tilting a mower on its side can cause oil to leak into the filter for air. This can damage the engine and reduce its lifespan. When the mower is on its side, the carburetor can also become flooded with gasoline, making it difficult to start or causing it to stall.
Remove the oil fill tube`s dipstick and tilt the mower in the direction of the container until oil begins to drain out. Never turn the lawnmower upside down, as this will cause the carburetor to flood and could damage the engine.
Tilting a mower on its side can cause oil to leak into the filter for air. This can damage the engine and reduce its lifespan. When the mower is on its side, the carburetor can also become flooded with gasoline, making it difficult to start or causing it to stall.
It`s normal to have a few oil drips a few hours after an oil change. However, any more than that, and you`ll need to determine where the leak is coming from. There are several ways to determine if the leak is coming from the drain plug, such as the gasket part being worn or dirty.
It`s important to note that oil tanks cannot simply vent into the atmosphere, as this could lead to the oil leaking onto the operator during use. To avoid your chainsaw from leaking oil whist in storage, the best solution is to drain the chainsaw of its bar oil and fuel mix and store the chainsaw empty.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Ms 170 leaks bar chain oil out bottom, no oil on chain
ANSWER : Your clutch drum bearing has gone bad, letting the clutch drum to move around and cut into the oiler behind it, so now it just pumps the oil out that hole. You have to get that fixed to use the saw, otherwise you’re going to cause catastrophic damage to the saw very soon.

Read Full Q/A … : Troy-Bilt

Poulan 14″ gas leaks bar oil all over, plenty on bar/chain, using thin synthetic oil.
ANSWER : Use actual bar oil sold for that purpose. It’s thicker and won’t run out like water. Synthetic oil is very thin does not have the proper density.

Read Full Q/A … : Troy-Bilt

All bar oil leaks from the bottom in a stream while engine is running
ANSWER : Take bar and chain off and clean oiler its not ably to close so to speak

Read Full Q/A … : Troy-Bilt

My chainsaw leaks oil out of a small hole or drain just below the base of the bar. is there anyway to way to stop this
ANSWER : Are you sure you aren’t talking about the chain oiler system? There is to be a small amount of oil to lubricate the bar and chain.

Read Full Q/A … : Troy-Bilt

BURNING OIL MY TORO IS BURNING OIL ┬áTO THE POINT OF HAVING TO REFILL IT EVERY TIME YOU USE IT…
ANSWER : Look for leaks, make sure its clean motor and cooling fins, i would suggest to take it in to a shop, check you oil level too make sure your not dumpimg fuel into your crankcase. your breather valve my be bad to

Read Full Q/A … : Troy-Bilt

Pouring out oil.
ANSWER : Where is it pouring out from? Might you be over filling the mower? Is your drain plug tight? the right thread? (meteric vs non-metric?) if the casting is cracked, you are done. The other items are probably correctable.

Read Full Q/A … : Troy-Bilt

Pump oil leak where pump connects to engine
ANSWER : With that few hours, you need to return it as the seal shouldn’t leak. Probably was improper pump assembly, so you should take it back, because it will only get worse and fail. Hope this helps you, Rick

Read Full Q/A … : Troy-Bilt

What kind of oil is in the hydrostatic drive in craftsman snowblower?And how much?
ANSWER : 5W 30 and fill it just below the bottom of the fill hole.

Read Full Q/A … : Troy-Bilt