2490 Auto Reel 20m Hose 12.5mm
Lock in unlocked position ,when hose is pulled four clicks , hose cannot be pulled anymore
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Why does the Auto Reel not retract all the time? We recommend pulling out all the hose. Clean any excess debris from the outside of the hose such as sand and dirt with a damp cloth. Now, let the hose retract slowly by walking back to the reel holding the end stop.
A: No, we do not offer a repair service for Auto Reels.
The most likely cause is grit or dirt in the trigger. In which case, dismantle the trigger, clean thoroughly and replace. If the spray fails to shut immediately and continues to dribble out it could be due to air being trapped in the lance.
Firstly ensure that you are releasing water pressure from the hose before retracting. The added water pressure may be the cause of this issue. If this does not help, pull your hose out to its full length then let it retract back in. This should re-align the hose on the drum.
Low pressure at your garden hose spigot can be caused by one or a combination of issues, such as clogged or leaking pipes, excessive corrosion in the spigot valve or a lack of water pressure coming from the street.
The reason for this is because a build up of water pressure. On the water inlet or coupling the water can cause a pressure build up, popping the garden hose off. The aqua stop is a valve in the end of the garden hose connection that restricts water flow.
If you`re hose reel is leaking, there are only three possible sources for the leak: The inlet hose has failed. The brass swivel has failed. The connection between the inlet hose and the swivel has loosened.
You can now fix any small hose using the 12mm Retractable Reel Hose Repair Kit. This kit will enable you to cut out and repair the damaged hose section, so you can continue to use your hose reel.
Open the Water Valve
Gate valves have circular handles that you turn until it stops. Ball valves have a handle that runs perpendicular to the pipe when closed. Turn this valve 45 degrees so it sits parallel to the pipe. Once you do that, the water should be back on.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How can I fix a hozelock hose reel that has been pulled out too much and jammed?
You have to take the cover off and redo the hose you can re reel back in
Just installed a new pull cord…the cord does not retract. How do I fix the problem?
The best way i found is to twist counter clock wise a dozen turns,hold the spool with vise grips,feed the roop through all holes you need to go through, into the reel knot, i burn the knot, keeps it from slipping out,then slowly let the spring bring the slak in when i release the vise grips!
Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
No response to clarification request.
How can i fix a leak inside my hozelock auto reel
Just replace the O-rings inside. See pictures how to take it apart.
I can’t start it because the pull cord is stuck and it happened after I installed a new blade.
If the recoil assembly has three screws holding it in place, remove them, lift the recoil assembly off and see if it works off the mower. If it does, reassemble.
Hard to pull starter rope. It doesn’t pull smoothly. hard to pull.
Take the spark plug out–does it pull smoothly now? If not, the pull cord may be the wrong size or it is damaged and/or doesn’t rewind correctly. Does the machine have a compression release? If so, it may be plugged with carbon. With the spark plug out, pull the engine through several times briskly with the throttle open and the choke off to expel any excess fuel from the crankcase. Hope some of this helps!
Chain saw won’t start – pull starter pulley hard to pull?
If it worked fine the last time you used it, then pull the spark plug and try pulling the rope. See if it’s easier or if gas shoots out of the plug hole. I’ve seen this happen when the diaphram in the carb goes bad from sitting over winter. It loads up the cylider with fuel and makes it very difficult to pull the rope. If there is no fuel in the cyliner and it’s still hard to pull, make sure there is nothing binding the clutch/sprocket. I’ve had chucks of wook lodged in there that caused it to bind the crank output, which resulted in a hard pull on the rope as well.
I pulled the weed eater to start it and the pull cord stayed out and won’t return back it was working fine early about ten minutes before this happened need help with fixing can work on this myself if i can find out what’s going on “need help in St.Catharines”.
You need a new rewind spring most likely it comes as a part with the reel.