front one and mix gas and two cycle oil together and put it in the back at a 50 to 1 ratio or is the two cycle oil go in front and the gas go in back?
Homelite

Experienced gardeners share their insights in answering this question :
You Put mixed gas in the back, some chainsaws take a mix of 32-1 ratio. Check your manuel. Put the chainoil in the front.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

For longer-term storage, laying the chainsaw on its side on a shelf is your best bet. Release the pressure first when unscrewing the caps, then empty all fuel.
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs. The T screw regulates how much fuel is sent to the carburettor while idling until the throttle is pressed.
While you are using your chainsaw, it can start pulling to one side, making it difficult to cut straight. This may be caused by one of the following issues: The chain is dull or damaged; make sure that the chain is correctly sharpened. If you need to replace the chainsaw chain, use the correct one.
The easiest way to tell a 2-cycle engine from a 4-cycle engine is the number of fuel tank and/or oil sump fill ports. A 2-cycle engine has one fill port with a cap that has fuel pump and oil can icon. The cap will usually state the oil to fuel mix ratio.
While it`s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
Overbucking Chainsaw Technique

Also known as overcutting, this is the most popular technique for cutting trees. The technique is used to cut down a horizontal log of wood.

The sharpening angle will generally be between 25° and 35° – the harder the wood, the greater the angle. To maintain the correct angle, we recommend that you use a sharpening grid or a filing gauge as an aid.
If your chainsaw shuts down when turned sideways, it is usually because the fuel filter is held away from the fuel, as the position of the chainsaw has changed. The fuel filter must be able to stay in the fuel as the position of the chainsaw is changed.
Running a 2-cycle with the wrong fuel to oil mixture can cause severe damage to your engine. Running the machine without any oil mixed in the fuel can cause severe damage to your equipment within just minutes. This damage is generally very costly to repair and is usually irreparable.
Store in a dry place

Your chainsaw should be stored in a dry place. Choose a place which is well ventilated and protected from the weather. Keeping it outdoors is not advisable.

If your chainsaw shuts down when turned sideways, it is usually because the fuel filter is held away from the fuel, as the position of the chainsaw has changed. The fuel filter must be able to stay in the fuel as the position of the chainsaw is changed.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Do I need gas and oil mix – Poulan Super 250a Chainsaw Plate
ANSWER : I think Poulan uses a 40:1 ratio to one gallon of gas, however I have always used 50:1 the same as my sthl saws with no issue. I would rather have more oil mix that to little.

Read Full Q/A … : Homelite

What is ment by 50 to 1 mix
ANSWER : 50 to one is a ratio of fuel to lubricating oil. Typically 50 parts petrol/gasoline to one part two stroke oil.

Oil typically comes in a special plastic bottle that incoporates a measure. Simply squeeze the right ammount of oil into the little chamber and add to 5 litres of gas.

Read Full Q/A … : Homelite

How do u mix the 50/1 ratio oil and gas mixture
ANSWER : Mix 2 1/2 oz of 2 cycle oil into 1 gal of gas

Read Full Q/A … : Homelite

Do you mix gas and oil in this trimmer – Ryobi 30 Cubic Centimeter Curved Shaft Gas Trimmer
ANSWER : Yes. Verifythe ratio, either 40:1 or 50:1

Read Full Q/A … : Homelite

Ineed the proper mix for gas. for a Poulan pro 262 18in. chain saw.
ANSWER : Hi sephil99125…
50:1 oil to gas ratio
1 pint of 2 cycle oil to 6 gallons of gasoline
Please take time to rate me

Read Full Q/A … : Homelite

DCS520 PETROL/OIL RATIO
ANSWER : 40 to one is a good mix

Read Full Q/A … : Homelite

Oil ratio which is better, 25:1 or 50:1 ratio of oil and gas? Owner manual says anywhere in between these two ratios.
ANSWER : I use one of those small 2.6 oz oil containers in a gallon (128 oz) to give a 50:1 mix. If you want more oil in your mix add another container – but it will be more expensive and waste oil.

Read Full Q/A … : Homelite

I need the gas mix oil ratio for the Poluan Pro 42…
ANSWER : 40:1 gas to oil ratio.

Read Full Q/A … : Homelite