John Deere
The wire from the ignition switch broke off from where it was attached to can anyone tell where this wire attaches to on the other end it is still attached on the switch end.
Experienced gardeners share their insights in answering this question :
One wire go to 12v+
the ather one to the starter
if you can sand photo i will mark the place for you
injoy
the ather one to the starter
if you can sand photo i will mark the place for you
injoy
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Plastic Keys are designed to open the ground circuit contacts to the ignition coil when they are inserted. Plastic keys are not rotated after insertion. When removed, the ground circuit contacts come back together and ground the engine ignition coil and prevent the ability to start.
Once the ignition switch is prompted by key or the push of a button, it activates the voltage from the battery to the ignition coil to produce the engine spark. The engine spark from the coil or coils is directed to the spark plugs to ignite the fuel to make the vehicle run.
The ignition switch sends power to the starter motor, engine controls, and ignition controls.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Snow blower threw oil everywhere and will not move. Engine starts but does not move forward.
ANSWER : The gearbox for the drive has sheared a tooth off the gear to make it leak and not propel the wheels. it has cut into the seal making it leak
Read Full Q/A … : John Deere
Craftsman snow blower #536.886261,wire connection coming off coil 4 inches long,what does it attache to?
ANSWER : Sears Parts Online has a pdf of this unit. Have you checked there yet?
Read Full Q/A … : John Deere
Electric Maztang mt 968 auger wont run – Yard Machines 28" Two-Stage Snowthrower
ANSWER : The motor runs but the auger does not , if so the bolt snapped in half from hitting something that you should have not hit , this is a normal thing so as to not blow up the engine , it is a safety feature in all snow blowers , just get the right bolt or make one grind it down to where it will break easy but will work the auger , they sell them on ebay for a couple bucks but I make mine
Read Full Q/A … : John Deere
Snow blower gets bogged down in snow.
ANSWER : It sounds like your engine is running lean, see if you can adjust the high throttle mixture on the carburetor (if possible at all). If there is no adjustment possible, it may be the carb is clogged and needs some service. Try cleaning it or find a new replacement carb for it.
Read Full Q/A … : John Deere
How much oil does the snow blower hold
ANSWER : 725 ml
Read Full Q/A … : John Deere
Snow blower wont start
ANSWER : Clean the fuel out and the carb , make sure you are getting spark close the choke to start then shut if off or it will foul the plug
Read Full Q/A … : John Deere
My Toro snow blower requires leaded fuel. Can I
ANSWER : I would not reccomend it. just buy some lead additive at any auto store or automotive department & mix per the directions.
Read Full Q/A … : John Deere
Will not start – Yard Machines 24" 208cc Two Stage Snow Thrower
ANSWER : If there is an adjusting screw on the carb turn it out a little bit at a time and see if that works before you do anything else. If that don’t work put the screw back where you started.
If that doesn’t work take the plug out and install a new one and while the plug is out put a table spoon of gas in the spark plug hole and reinstall the plug and put the plug wire back on. If the engine starts but stalls after the little bit of gas is used up. Take the bowl off the carb and clean it out as well as clean the fuel jet that is in the bolt that holds the bowl on. Put back together and see if that works. It is quite often dirty gas that is the problem. Especially if its been sitting. Oh yes put fresh gas in it as well.
If that doesn’t work take the plug out and install a new one and while the plug is out put a table spoon of gas in the spark plug hole and reinstall the plug and put the plug wire back on. If the engine starts but stalls after the little bit of gas is used up. Take the bowl off the carb and clean it out as well as clean the fuel jet that is in the bolt that holds the bowl on. Put back together and see if that works. It is quite often dirty gas that is the problem. Especially if its been sitting. Oh yes put fresh gas in it as well.
Read Full Q/A … : John Deere
