John Deere
LX277
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
It could be your bearings and your spindle pockets, or spindles, have seized up,” says Oshel. If the blades are stuck, pump some grease into the fitting and carefully work the blades back and forth by hand until they move freely.
If/when the PTO exceeds the preselected RPM setting, the EOC will de-energize the solenoid valve, disengaging the PTO.
A PTO draws its power from the vehicle`s engine, but it cannot start transferring that power until it has been engaged. PTOs can be engaged through air pressure, hydraulic pressure, or a cable, explains Luke Hart, customer/employee technical training instructor for Muncie Power Products, a manufacturer of PTOs.
This operation is crucial to the overall functioning of riding mowers, and thus PTO clutch repair may need to be immediately performed on riding mower models that have a failed clutch. Fortunately, you can fix your clutch irrespective of your experience with PTO clutch installation.
When the Power Take Off (PTO) switch is turned ON, 12 volts is sent to the PTO solenoid to engage the PTO. This sends transmission pressure to the PTO to engage. When pressure is sensed, the PTO pressure switch sends a signal (usually ground signal), to the chassis controller indicating that the PTO is engaged.
The possible causes of a lawn mower blade spinning but not cutting grass include a damaged or wrongly installed blade, a dull blade, or damaged lawnmower tires. Other possible reasons can be improper tire pressure, a clogged deck, or a broken mower belt.
If your John Deere won`t crank and all you hear are clicking sounds when you turn the key, you likely have a bad battery or a bad connection somewhere between the battery and the starter. Double check that the alternator and battery connections are clean and tight.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
My john deere z425 start fine but does not move
ANSWER : Check drive pulleys and belts.
Read Full Q/A … : John Deere
Cannot remove mower blade pulley nut – John Deere 22HP VTwin 48" Riding Mower
ANSWER : I think its a left hand thread, you undo it clockwise (the “wrong” way)
Read Full Q/A … : John Deere
John deere stx 30 pto wont engage
ANSWER : Check your fuse or for a broken wire( or shorted)
Read Full Q/A … : John Deere
I am trying to find a new or second-hand bonnet for my john deer stx38. i live in the gippsland area. any suggestions?
ANSWER : I use www.greenpartstore.com
Read Full Q/A … : John Deere
My Tractor (425) won't start – John Deere 420,1020,2010,2020,2510,2520 Tractor Float
ANSWER : If you have no spark the first thing to replace the time delay module on the left rear side of engine. Its black and about 2 inches by 1 inch with yellow,red,orange and black wires going to it. Replacement is round shaped with same amount of wires.If no fuel to carb check for flow at filter, if theres flow but no pressure look for a split fuel line in tank between pump and sender.
Read Full Q/A … : John Deere
The mower blades on my John Deere stx 38 lawn tractor will not engage. I just installed a new pto switch and when engaged the engine stops.
ANSWER : It sounds like the safety switch under seat is bad
Read Full Q/A … : John Deere
Mowerdeck will not engage… – John Deere 195HP Hydrostatic 42" Cut Riding Mower
ANSWER : I own a similiar John Deere model (L130, 23HP with a 48″ deck). I would check the electric clutch (called a PTO). To do this check the wires to this clutch and look for something disconnected. These wires (to this PTO clutch) should have twelve volts with the key on and the blades engaged.
Read Full Q/A … : John Deere
PTO CONTROLS. How do you engage and disengage PTO.
ANSWER : The tractor is not a 6300 is it.If it’ not you need to adjust the cable for the p.t.o. until it will stay down.Don’t turn the turnbuckle too much at a time because there is a fine line between the won’t engage and the won,t disengage adjustment.
Read Full Q/A … : John Deere
