Experienced gardeners share their insights in answering this question :
Check the fuel filter to make sure its not clogged then check the float in carb as well if that doesn’t work e-mail me @ [email protected]
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A faulty or dirty spark plug could be the reason your lawn mower won`t stay running. It might produce the initial spark, but the spark won`t be enough to keep the engine running if the plug is clogged with dirt and oil. Spark plugs are usually located on the front of a push lawn mower and connected to a black cable.
If your John Deere won`t crank and all you hear are clicking sounds when you turn the key, you likely have a bad battery or a bad connection somewhere between the battery and the starter. Double check that the alternator and battery connections are clean and tight.
A dirty carburetor is the most common cause of a lawn mower that starts and then dies. Other possible causes include: Stale/Dirty Gas. Faulty Choke.
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that`s happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
Use Carburetor Cleaner
Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleanerOpens a new window, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.
The spark plugs are worn or damaged
If you find that your lawnmower keeps dying, or keeps stalling while cutting grass, then inspect the spark plugs. Look for signs of damage or wear. Something as simple as a cracked porcelain insulator can mean an electrode has been damaged or burned away.
If you just hear a whirring sound like the starter motor is spinning without affecting the motor, then the solenoid is either broken, or there`s a wiring issue on the starter itself. Options are: have the starter rebuilt, replace the whole thing, or see if you can track down the wiring issue on the starter.
Common problems on the list include things like uneven grass cutting, slipping belts, or minor engine problems. John Deere also claims that lighting issues and battery problems are common. Still, John Deere tractors are largely reputed for their reliability.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have John Deere GX345. It does not start consistently. When it doesn’t start the plugs have no spark. The problem is intermittent.All electrical connections look clean and no corrosion. Re- seated all connections. Fuel flow is good because I can smell raw fuel while cranking the motor. I replaced the fuel lines last year. Thank you for your help. Daryl Witowski
Look for a small silver box with 1 wire on it mounted to the motor. It is a temp sensor and will keep it from firing…Just had to replace mine…
My Tractor (425) won't start – John Deere 420,1020,2010,2020,2510,2520 Tractor Float
If you have no spark the first thing to replace the time delay module on the left rear side of engine. Its black and about 2 inches by 1 inch with yellow,red,orange and black wires going to it. Replacement is round shaped with same amount of wires.If no fuel to carb check for flow at filter, if theres flow but no pressure look for a split fuel line in tank between pump and sender.
Problem starting every time when starting cold I have to crank engine several times, after it runs it will start every time until it sets for a few days, then back to the repeated cranking.
Thats perfectly normal
My john deere z425 start fine but does not move
Check drive pulleys and belts.
Spake plug is not spakeing – John Deere Original 130 160 165 175 180 185 Operators
Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.You do this by grounding the plug on the head of the engine and cranking the engine or by pulling the crank rope…watching the plug for spark.If you are getting a nice blue spark then skip A below and go to B.
A…If you do not get a nice blue spark then you may need to replace the electronic module.Note: If you have to replace the module be sure to measure the position it is in, it is critical to starting.The clearance can be measured with a “business card”…use the card for the right clearance between the coil and the flywheel.Take a picture for later reassembly.
B…Also take some fine grit sandpaper (not emery) and lightly sand the flywheel where the magnet is located to clean any rust or corrosion from the magnet area.Please rate meBud
How do i replace a clutch on a JD 3020 tractor
Break it in half, then get with it.
Looking for information on a John Deere tractor S/N CH0850S017329 and the current estimated value of this tractor with approximately 2,700 hours on it.
Can you please post the model number of the tractor? Thanks
Free belt diagram john deere freedom 42 – John Deere 42 in. EZ Trak Bagger