John Deere
Experienced gardeners share their insights in answering this question :
It could be a blocked sensor.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
By keeping it simple, the baler comes in the affordable range of $21,000 to $22,000. For comparison, the next model in the 9 series lineup – the 459 – starts around $25,000 and goes up to $35,000, depending on the options selected.
The round baler picks the hay from the ground and feeds it into the bale chamber. The hay is then wrapped onto itself by means of six to eight long rubber belts which are around 7 inches wide. As extra hay is picked up and drawn into the baling system, the bale becomes spherical and fills the bale chamber.
Baling is a process that compresses material into a block (bale) which is secured by plastic or wire strapping. The process reduces the volume of the material which: Reduces loose waste on site. Reduces transportation/waste disposal costs.
We estimate a “lifetime” as 15 years. However, it is quite common for well-maintained balers of good production quality to have a longer lifespan than 15 years.
If you are buying a baler first, keep horsepower requirements in mind when pairing with a tractor. PTO horsepower requirements for round balers start at 30 hp and can run up to 120 hp.
The basic functional components or units which make up a baler for rectangular bales are the pickup and elevating unit, feed conveyor, feeder, compression chamber and the tying mechanism.
Rectangular pick-up baler
It is powered from the power take-off (PTO) of the hauling tractor. The straw windrow is lifted from the ground by a pick-up reel having spring teeth (14) and transferred continuously to a conveying and feeding mechanism (3) as the baler moves forward along the windrow.
The basic functional components or units which make up a baler for rectangular bales are the pickup and elevating unit, feed conveyor, feeder, compression chamber and the tying mechanism.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have John Deere GX345. It does not start consistently. When it doesn’t start the plugs have no spark. The problem is intermittent.All electrical connections look clean and no corrosion. Re- seated all connections. Fuel flow is good because I can smell raw fuel while cranking the motor. I replaced the fuel lines last year. Thank you for your help. Daryl Witowski
ANSWER : Look for a small silver box with 1 wire on it mounted to the motor. It is a temp sensor and will keep it from firing…Just had to replace mine…
Read Full Q/A … : John Deere
My Tractor (425) won't start – John Deere 420,1020,2010,2020,2510,2520 Tractor Float
ANSWER : If you have no spark the first thing to replace the time delay module on the left rear side of engine. Its black and about 2 inches by 1 inch with yellow,red,orange and black wires going to it. Replacement is round shaped with same amount of wires.If no fuel to carb check for flow at filter, if theres flow but no pressure look for a split fuel line in tank between pump and sender.
Read Full Q/A … : John Deere
Problem starting every time when starting cold I have to crank engine several times, after it runs it will start every time until it sets for a few days, then back to the repeated cranking.
ANSWER : Thats perfectly normal
Read Full Q/A … : John Deere
How do i replace a clutch on a JD 3020 tractor
ANSWER : Break it in half, then get with it.
Read Full Q/A … : John Deere
Looking for information on a John Deere tractor S/N CH0850S017329 and the current estimated value of this tractor with approximately 2,700 hours on it.
ANSWER : Can you please post the model number of the tractor? Thanks
Read Full Q/A … : John Deere
Spake plug is not spakeing – John Deere Original 130 160 165 175 180 185 Operators
ANSWER : Hi Lloyd
Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.You do this by grounding the plug on the head of the engine and cranking the engine or by pulling the crank rope…watching the plug for spark.If you are getting a nice blue spark then skip A below and go to B.
A…If you do not get a nice blue spark then you may need to replace the electronic module.Note: If you have to replace the module be sure to measure the position it is in, it is critical to starting.The clearance can be measured with a “business card”…use the card for the right clearance between the coil and the flywheel.Take a picture for later reassembly.
B…Also take some fine grit sandpaper (not emery) and lightly sand the flywheel where the magnet is located to clean any rust or corrosion from the magnet area.Please rate meBud
Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting a bright blue spark at the spark plug.You do this by grounding the plug on the head of the engine and cranking the engine or by pulling the crank rope…watching the plug for spark.If you are getting a nice blue spark then skip A below and go to B.
A…If you do not get a nice blue spark then you may need to replace the electronic module.Note: If you have to replace the module be sure to measure the position it is in, it is critical to starting.The clearance can be measured with a “business card”…use the card for the right clearance between the coil and the flywheel.Take a picture for later reassembly.
B…Also take some fine grit sandpaper (not emery) and lightly sand the flywheel where the magnet is located to clean any rust or corrosion from the magnet area.Please rate meBud
Read Full Q/A … : John Deere
My john deere z425 start fine but does not move
ANSWER : Check drive pulleys and belts.
Read Full Q/A … : John Deere
Free belt diagram john deere freedom 42 – John Deere 42 in. EZ Trak Bagger
ANSWER :
Read Full Q/A … : John Deere
