Garden

While mowing, I hit a root and jammed the mower. I cleared the root from the mower deck and checked the blades to ensure they were free spinning. Now when I pull the PTO swith, I hear a click, but nothing happens. I checked the fuse and it was good.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
It could be your bearings and your spindle pockets, or spindles, have seized up,” says Oshel. If the blades are stuck, pump some grease into the fitting and carefully work the blades back and forth by hand until they move freely.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it. Need help finding your model number? The PTO switch provides power to the PTO clutch.
If/when the PTO exceeds the preselected RPM setting, the EOC will de-energize the solenoid valve, disengaging the PTO.
Worn or broken blade drive belt – If the riding mower blades are not spinning, the blade drive belt may be worn or broken and unable to engage the blades. If the belt is intact, inspect it to see if it`s loose or slipping on the pulleys then replace it with a new one if necessary.
The possible causes of a lawn mower blade spinning but not cutting grass include a damaged or wrongly installed blade, a dull blade, or damaged lawnmower tires. Other possible reasons can be improper tire pressure, a clogged deck, or a broken mower belt.
There is a safety switch at the end of the cutter engage lever which has gone faulty and needs replacing, overiding the switch by keeping it pressed in will allow the mower to be operational till replacement switch is fitted.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.

Hope it helps.

Anthony

Read Full Q/A … : Garden

Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only

Read Full Q/A … : Garden

I have had a poulan pro 550 series push mower for almost 1 year at the end of the season last year the mower would start briefly and then stop. i have cleaned out the air filter and that did not help.the mower started, i made one revolution around the yard 3/4th of the way the mower quit. I then primed the mower it started then quit and now it will not start at all. Does anyone have any suggestions of what to do. Thanks
ANSWER : There is a little spring that works the carburetor arm. If that popped off then the mower will not run.

Read Full Q/A … : Garden

B&S Quantum Power 4hp won’t start with fresh plug,
ANSWER : Did it run before you changed the plug?Gap is correct, flywheel shear pin may be bad, Water in the Gas?

Read Full Q/A … : Garden

My toro 6.5 hp push mower (2010), has no fire to the plug. I have not abused it. i have a small yard and it just gets normal use. Now it won’t fire. I first changed the fuel and cleaned the carb thinking it was that crappy ethanol again. but i grounded out the spark plug and cranked it…no spark. I think it has to do with the lever you pull back to start it . they have some stupid complicated safety contraption that rides along the fly wheel when you pull back on the handle for starting and shutting off the engine. …it looks worn out already…like a mini brake pad. any ideas?…do i really have to replace this garbage every year or am i on the wrong path here?
ANSWER : Unhook your wire from the coil that goes to shut off mechanism, and see if you have spark then. the wire may be grounded out, or your coil might have took a ****

Read Full Q/A … : Garden

Lawn mower cranck but wont start…
ANSWER : Since you already checked for spark and air I would drain all the fuel out of it and check that fuel for water. Over time some lawn mowers end up with contaminated fuel. You can see the water sitting on the bottom of the fuel if you let it stand for a bit in a small plastic bowl.

Be sure to empty and dry out you fuel can as well. Especially if the mower stopped running right after a refuel. Which is a good sign your gas can is contaminated too.

Read Full Q/A … : Garden

My mower will start but won't stay running – Toro LX466 22HP Lawn Tractor 13RT61RH244
ANSWER : I am going to respond 2 times to this post. The first reply will be generic things to check.
First off check the oil level and make sure it is serviced to full.
If your having a lack of fuel (runing lean) you will need to check fuel flow at the carb fuel mainfold. It should fill a spray paint can lid in less than 10 seconds but teting flow rated of the main fuel line. If you have poor flow here… you need to check the fuel filter and the fuel tank outlet port for obstructions.

Good Fuel flow still shutting off…. remove the carb float bow and clean the debris from the bow’ and the treaded area where the fuel solenoid mounts Additionally you will have to again remove the main fuel line and spray carb cleaner in the float needle area to flush out any debris through the fuel hose connection.

For the second response I need to know which engine is installed on your mower by MODEL number if you can locate it. (there are 3 engines) At least try to find the engine model number. If you can not locate it Brand and HP of the engine (I assume 22 hp) Thanks for choosing FixYa,
Kelly

Read Full Q/A … : Garden

Lawn mower motor runs good, the drive wheels run good but the blade won’t stay enguaged. Thanks
ANSWER : Check your cable that controls the blade engagement.

Read Full Q/A … : Garden