Worx
Jaw saw chain falls off after a couple of cuts. I’ve repositioned it as shown in the manual and it still falls off. What am I doint wrong?
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A common issue with pendant necklaces is when the chain moves and the clasp suddenly sits in the front. This is because the clasp is likely heavier than the chain itself. To prevent this from happening, look for a necklace that has a counterweight on the clasp, or add one yourself.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Chain keeps falling off – Poulan 18" Chain Saw Replbar (small Saws)
ANSWER : Your chain is too loose. If you’re using an old chain, you might need to have a link taken out of it. You can find replacement chains for your saw at Hyperparts.com. Use the application lookup link at the top of the page with your model # to make sure you order the right chain.
Read Full Q/A … : Worx
The chain keeps coming off and we just got it today.
ANSWER : Sounds like you do not have the chain tight enough. Read the book if it came with one. Good luck
Read Full Q/A … : Worx
Chain falls off
ANSWER : Not adjusted correctly
Read Full Q/A … : Worx
Chain keeps coming off – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Open the chain guard.Once there look for a bolt that hold the chain plate.The chain plate has a large groove and the bolt.djust the chain by plull to the front until the chain is tight,but not too much,just test by hand if is move freely but tight.Reverse the procedure.If you need more help come back.Post / thumbs / testimonial are welcome!
Read Full Q/A … : Worx
My 18 Inch chain saw will not keep oiling the Chain, I had it worked on and He said it was plugged. How do you unplug it with out taking it all apart. Is there a spot to blow air through. the Preacher..
ANSWER : Remove the chain bar and look just below the bolts holding it in place. You’ll see a small hole where the chain bar oil pump pushes out oil. Make sure this hole is clear then run the saw without the bar on.
Be CAREFUL of fingers!
You should see oil coming out of that hole. If not, you may need more serious work done with the saw (chain bar pump replacement).
Read Full Q/A … : Worx
Bad Clutch?? 455 rancher 20″ bar) I have owned it for two years and cut tons of fire wood with it. I recently replaced the oil pump. Yesterday I’m cutting oak like butter. Chain saw is cutting fine.. For no apparent reason it starts struggling to cut. I figure I hit something with the chain. I go to sharpen and notice that the clutch it’s red hot. I take it apart clean it up sharpen it up put it back together fire it up and start to cut. It starts to cut on angle and has no power?? runs fine revving it but will not cut?? What do you think?
ANSWER : Hi Before other checking change the spring of the clutch(2). best regards savumihai71
Read Full Q/A … : Worx
What causes the chain on my 240E to jump off the chain bar often, the chain tenson is correct.
ANSWER : Is the bar bent?try and flip it over and see if it falls off the other side if you can see a bend
Read Full Q/A … : Worx
I was using the saw as a chain saw last weekend to cut up an old tree stump when the chain came off. I don’t know how to access it to put it back on and don’t have a user manual. The saw belonged to my late father and I don’t know if he even kept the manual.
ANSWER : You will have to remove the cover on the side the chain bar goes into. There should be one or two nuts holding the cover on the side. The is also a chain tension adjuster you may have to loosen to put it back on. Make note of the direction of the teeth on the chain. It is an directional chain. The tension adjuster is usually a flat head screw on the front side right beside the chain bar.Unless it is a really old saw, manuals are available from most manufacturers for free download. See if you can locate a brand name and model number.
Read Full Q/A … : Worx
