How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

To find the model number, look for a model number sticker on the engine. All Honda engines model numbers start with the letter “G,” such as “G100”, “GX610”, or “GXV160.” This is the base engine model. The engine model and serial number should be adequate for most of your needs.
The engine serial number is stamped into the side of the engine. All Honda engine serial numbers have a 4 or 5 letter prefix followed by a 7 digit number.
Honda Lawnmower Serial Number Location

On Honda lawnmowers, the model numbers and serial numbers are usually located on the back of the deck between the handles.

You can find your VIN on your windshield, in the door jamb, or on your registration or insurance card. The radio and navigation serial numbers are located on an anti-theft card or sticker inside your glove compartment. If you can`t find it, you may be able to retrieve your serial number electronically.
Finding your model number and serial number is as easy as locating the identification tag on your machine. As seen in the example, the model number will be displayed below the MODEL heading (Example: Z235), and the serial number will be underlined on the top-right corner of the tag (Example: 130002).
VIN stands for Vehicle Identification Number. It includes a set of individual numbers and letters, each providing specific information about your vehicle. The VIN number will tell you where your car was made, who manufactured it, vehicle-brand, engine size, year of the car, what plant assembled it and more!
The tenth character of the VIN within the Vehicle Indicator Sect (VIS) of the VIN, denotes the motorcycle`s model year. The characters used to identify the year in the VIN use both letters of the alphabet except I (i), O (o), Q (q), U (u) and Z (z) and numbers from 1-9.
Honda Power Equipment HRS216VKA GCV160 Self Propelled.
You can find the model and serial number on the top of the mower and near the left rear tire.
Honda Power Equipment HRS216VKA GCV160 Self Propelled.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Filter case for honda lawn mower
ANSWER : Go to a honda lawn mower dealer
go e-bay and type in air filter housing for honda lawn mower

Read Full Q/A … : Honda

<!– from fixya rte –>Electrical diagram for Honda GX390 – Honda Gx390 Motor Inside Cover
ANSWER : Check out the manual here

Read Full Q/A … : Honda

ANSWER : BEFORE you go thru all of the advice and look at most other Honda web
info…..go and buy a brand new spark plug and start with that! It
appears Honda used a NGK spark plug in the past that fails after some
time….giving the syptoms of problems with the carb, runs for 10-30 seconds, sticky valve, etc.

Do not try to clean and use the old spark plug!!

Check this out….it was the answer I was looking for after hours of
work, reading, and talking to Honda dealers —-

Read Full Q/A … : Honda

What type of oil doesa honda gcv60 use?
ANSWER : GCV160 engines take 10W30 oil.

Read Full Q/A … : Honda

My Honda 160cc lawn mower engine cut out when I hit a large clump of grass. Now I cannot get it to start. Has always started with no problems. What to do?
ANSWER : Has probably broken flywheel key ….. putting it out of time

Read Full Q/A … : Honda

Honda HRR216 does not start at all ,what could be the problem
ANSWER : Hi arshadmalik5…

Check to make sure you are getting fire/spark at the plug, if so then do the following:Check/Clean/Replace your fuel filter if you have one.If the mower/weedeater/edger is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.Sounds like you will need to clean the carburetor or replace your carburetor internal rubber parts like the diaphgram and O rings.Be sure to use compressed air to blow out all the fuel and air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Sometimes you can get by with priming the carburetor or using starting fluid and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Keep in mind that the float for the carburetor must be level when you go to reassemble the carburetor or follow the instrucitons you get with the carburetor kit.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their orginal position before you started.
This is a FREE answer,Please rate me

Read Full Q/A … : Honda

How to take off carbarator – Briggs & Stratton Briggs Stratton Lawnmower Lawn Mower Short Block
ANSWER : Usually there are two screws. On some newer mowers the same screws hold on the Air Cleaner housing.

Read Full Q/A … : Honda

I need to know the spark plug for a Yardman by MTD 12A-556Q713 self propelled walk behind lawnmower (honda engine)
ANSWER : Your best bet is to take your old plug out and a parts store can duplicate it.

Read Full Q/A … : Honda