Experienced gardeners share their insights in answering this question :

I have found you a manual, all you need to know is inside please download and enjoy.

Below is a link showing you how to set your blades up.


How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

RYOBI provides two magnets to lift the knives for changing, and a hex wrench for removing the blade cover, vacuum diverter, knob, etc. The top has handy, integrated storage for both.
A thickness planer (also known in the UK and Australia as a thicknesser or in North America as a planer) is a woodworking machine to trim boards to a consistent thickness throughout their length. This machine transcribes the desired thickness using the downside as a reference / index.
We recommend sharpening to roughly 600 grit. Any finer and the resulting edge gained will only last a short time. Use a diamond hone to refine the edge and remove any burr from the back and bevel of the jointer or planer knife.
Electric Planer Blades

Top Tip – Some of these Power Planer Blades are universal meaning they can be used also with other brands of Planer.

“With the electrical control of magnetism, you use a capacitor in which one element is magnetic and, simply by charging the capacitor, you change the direction of the magnetism, say from being in the plane of the film to being perpendicular,” says Barnes.
Safety glasses and hearing protection are required.

Remove tie, rings, watch, other loose clothing and jewelry, and roll up sleeves. Never wear gloves when operating planer. Don`t raise or lower table while stock is in planer. Always run dust collection with planer.

The 2-speed gearbox allows you to change feed speed to optimize cuts per inch. This thickness planer also has a removable material gauge and extra-large thickness scale that ensures accurate cuts with every pass.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Ryobi No Fire at spark plug – Ryobi 30 Cubic Centimeter Curved Shaft Gas Trimmer
ANSWER : Have you checked just the plug wire for spark. If you’re not getting any here, then you may have a bad magnet-or. So if the spark is happening only at the wire and not through the plug. Change the plug. Also check the cut off switch. It could cause the no spark, to keep it from starting.

Read Full Q/A … : Ryobi

Switch keeps cutting out. Have used the chainsaw for about an hour in total. Is there anyone in South Australia who repairs these things????
ANSWER : Service Locator

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH

Read Full Q/A … : Ryobi

Ryobi PCN 4545 starts perfectly but chain will not turn.
Can you help?
ANSWER : Hi, have you released the chainbrake? Regards Phil.

Read Full Q/A … : Ryobi

Sparkplug gap for ryobi 410r 31cc tiller – Ryobi Cultivator
ANSWER : -Most small power equipment’s spark plug are pre gap. You don’t have to.

Good luck


Read Full Q/A … : Ryobi

My Ryobi portable table saw BTS20 just quit working in the middle of a cut.
ANSWER : Me id look at the under side of saw , id bet the saw just tripped out in use and needs to be reset , id also bet the reset is marked in red some place around motor

Read Full Q/A … : Ryobi

No local Ryobi dealer; what other brand chains will fit my 18″ Ryobi ?
ANSWER : Any saw service dealer can fit a chain to your saw. ‘Oregon’ saw makes bars/chains for about any saw made in the last 50 years or so. Just take the chain itself in to get a replacement. Good luck!

Read Full Q/A … : Ryobi

Ryobi 18V blower model p2100A has a broken impeller. How do I get a replacement part?
ANSWER : Ryobi does have an impeller that fits the 40400 model which is a bigger 40v unit! however the fan looks the same in the pic,

I’m guessing it may be scaled up to a larger size but perhaps have the same thread pattern?

anyway we love our two p2102 blowers they keep the porches and decks happy!

I’m gonna buy a few impellers and try to finagle them!

my guess is I may have to hook them up to a drill and use a file to cut them down to size (like you would use a wood lathe)

thus keeping the thing round and true

hope this helps I found the thing on ereplacementparts.com

price 2.60$ per impeller, worth a shot!!

ill post a youtube if this works!

Read Full Q/A … : Ryobi

42 inch mower cuts uneven, what is the problem?
ANSWER : Several things here could be the problem. Check to see if mower deck is level, measure distance on both side on a level surface. Check tire’s for low air. If you’ve replace the mandrel’s lately, some have a left & right side & if not put back together properly this will cause uneven cutting

Read Full Q/A … : Ryobi