Hooked to separate battery an it draws 4.5 amps but doesn’t work.
Experienced gardeners share their insights in answering this question :
You mean,you want it to turn??,if it is drawing power then it is working,it doesnt turn without the motor running,do you understand??
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
A clutch that won`t engage at all means there is serious damage somewhere. Check for a bent linkage, a seized slave cylinder, or a seized throw-out bearing. Beyond those, check for binding in the linkage, a corroded cable, or a failed friction plate.
Sudden failure is most often caused by a broken or loose clutch cable, linkable or a failed hydraulic master/slave cylinder. There can also be leaks in the hydraulic line or even the disc could be contaminated with something like dirt or debris.
A company gives its employees a set amount of PTO hours, which reset annually. Some employers reset PTO hours by hire date; others reset them on January 1.
This operation is crucial to the overall functioning of riding mowers, and thus PTO clutch repair may need to be immediately performed on riding mower models that have a failed clutch. Fortunately, you can fix your clutch irrespective of your experience with PTO clutch installation.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
John deere 240 brand new electric clutch. went I throw the swtich it clicks but doesn’t engage….
Adjust the clearance between the plates,9/16 wrench and turn the three nuts on the clutch one at a time about 1/4 turn each,retry the clutch,repeat until it works normally.
Cub cadet lt 1050 electric pto want engage??????????
Make shure pig tail is hooked right
Where is the fuse located on a LT1554 cub cadet
Check the connector and wires at the pto clutch. Sometime the movement will create a cut in the wiring you may be able to see. If so if the wire touches ground it will blow the fuse and if the wires touch each other it will short.
if the short is not there then the clutch is bad?BMW PARTS
How do i get the upper pulley above the pto clutch
Remove the pto unit and then remove the above pulley easely, spray some nut buster on the pulley and it will come off
How to change out an electric clutch on a cub cadet zero turn RZT50?
Removal is simple if you have access to an impact wrench so you can the center retaining bolt.
When re-installing anti-seize compound needs to used on the crankshaft so the new clutch assembly doesn’t seize on the shaft. To tighten the center bolt you must hold the flywheel in place by blocking it. This center bolt must be torqued to 45-55 ft fts. Also the new pto clutch needs burnishing in. Most new clutches come with instruction on this procedure.
I have a electric pto that come off a cub cadet and the part number of the pto is 5219-25 its a warner. My question is one of the wires have pulled loose in side the magnet are there any way to remove the magnet or take the pto apart? the wire is broke off inside the magnet. Thank you
Most likely you cannot repair this as the wire ususally breaks off inside. If you remove the assembly, you can see where the wires go into the potted coil. If there is no excess wire to reconnect to then your only choice is to replace.
With a cub cadet model #2518 year 2003 what engines can be used for replacement? Does it have to be vertico or horizontal?
I would replace with the same kind
While cutting grass the pto clutch cuts off, i have to push switch in and back out to restart blades. I have replaced the switch and pto clutch
Pto kicks in and out while mowing was wondering if its electrical or something else i have a jd 420