Garden

Diadrams and how to install deck belt
Experienced gardeners share their insights in answering this question :
Try this

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The smooth side of the belt goes on smooth pulleys (as shown on the idler pulley pictured above), while the ribbed side wraps around the grooved pulleys.
The “Deck Belt” goes around the pulleys right above the blades on the deck and then to a double pulley. The “Drive Belt” on your mower goes from the transmission, around an Idler pulley then over to the double pulley I mentioned before. The Drive belt also plays a role in making the wheels turn.
A perfectly tight mower belt can rotate without slipping off but not cause the engine to over-exert and overheat. If the belt does not slip off while working and is not producing unfavorable sounds that indicate wearing off of the belt, then that is the perfect tightness for it.
The “Deck Belt” goes around the pulleys right above the blades on the deck and then to a double pulley. The “Drive Belt” on your mower goes from the transmission, around an Idler pulley then over to the double pulley I mentioned before. The Drive belt also plays a role in making the wheels turn.
A perfectly tight mower belt can rotate without slipping off but not cause the engine to over-exert and overheat. If the belt does not slip off while working and is not producing unfavorable sounds that indicate wearing off of the belt, then that is the perfect tightness for it.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My john deere z425 start fine but does not move
ANSWER : Check drive pulleys and belts.

Read Full Q/A … : Garden

V-belt route installed on 48″ deck of John Deere LA130
ANSWER : Http://jdpc.deere.com/pimages/PU00/PU00859________UN28APR08.gifCopy and paste this in your address bar and it should take you to a picture of how to route the belt

Read Full Q/A … : Garden

I have vibration in the deck and have checked for a warped deck, busted spindles, and bent blades
ANSWER : Depending on the machine?? check or replace the cutter belt and also check the v pulleys for alignment

Read Full Q/A … : Garden

L110 bagger installation
ANSWER : I can’t help you on the bagger hole location. But you will need quality hi-lift blades. “Gator-Blades” are some of the best. At www.mowpart.com or Amazon.com

Read Full Q/A … : Garden

HAVE A JOHN DEERE 318 LAWN TRACTOR, CHANGED POINTS AND CONDENSER, WON’T TURN OVER, TRIED STARTING FLUID IN CARB AND NOTHING. CAN IT BE THE COIL AND HOW DO I CHECK? THANKS
ANSWER : Check the coil impedance on the primary and secondary side. You’ll have to disconnect the battery negative cable so you don’t short something out. Unplug the spark plug wires and the two sets of smaller wires connected to the primary side of the coil. The primary coil reading should be between 3.7 ohms and 4.6 ohms while the secondary (spark plug side) should be between 34.2 k-ohms and 41.6 k-ohms. If the resistance values you measure are outside of these ranges, you need to replace the coil.

Read Full Q/A … : Garden

My 1979 111 john deere lawn tractor deck blades shut off
ANSWER : If it has a clutch, that would be the problem. An electric clutch will kick on and off when it is hot if it is bad.

Read Full Q/A … : Garden

What size – Length belt fits L110 – John Deere L100 Series
ANSWER : Model # GX20072 is for a 42 inch deck . It fits a variety of John deere mowers

Read Full Q/A … : Garden

How do i replace a clutch on a JD 3020 tractor
ANSWER : Break it in half, then get with it.

Read Full Q/A … : Garden