Lawn Mower With Toro Power Tools

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Most lawn mower blades rotate in a clockwise direction (counter-clockwise when viewed from below), and as such have the cutting edge on the right side. If you are unsure of how your mower rotates, check the position of the discharge chute; if it is on the right side angled back, the blade turns clockwise.
Step 3 – Loosen the blade bolt

Wearing safety gloves, begin to loosen the blade bolt by turning it counter-clockwise. Depending on the type of lawn mower that you have, there may be one or several heat treated blade bolts to undo, which may or may not have special washers attached to them.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on

When i pull the rope it backlashes half way through the pull
ANSWER : Hi, You have most likely sheared the flywheel key which puts the timing out. Remove the flywheel and replace the key. Regards Phil.

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.

Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?

What should I do? Spark Plug? Turn wrenches?

Please let me know

ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.

Broken pullcord the pull cord on my cub cadet push mowersnaped and broken and we put it back in and know it wont wind back in
ANSWER : Yeah I got the same problem. My pull cord broke in the first season. On my own once the plastic cover is removed, 4 phillips screws, the cord housing is secured by 3 10mm nuts. Remove them and lift out the housing. On my own unit the spring had also slipped out of the mount on the shaft securing the assembly (another 10mm socket nut will loosen that) and I had to resecure that first, then wind it up before making the knot.. I used a Briggs and Stratton cord from another (truly dead) mower and have had no problems since then.

Trying to replace the pull cord , can’t get last housing off to get to coile up old cord , the shaft has a nut on the end that the auger screws into but i cannot get that piece off as there is no where to put a wrench to stop the turning of the engine shaft so i can torque the nut in the other direction to get it off , what do i do to get this pull cord replaced?
ANSWER : Use an impact wrench it will hit the nut so fast it will loosen it befroe the engine car turn over

How do i replace a pull cord on a xt7 pressure washer
ANSWER : Try this link:http://www.youtube.com/watch?v=Q3NjVomUQJMThere are others there as well.Best regards, –W/D–

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Broken pull cord
ANSWER : You have to take four allen screw out of the plastic that holds the engine on. There is also one by the spark plug that needs to come out. Once the engine is loose, you have to unplug one wire and unscrew the other. Then the engine should come off. Then loosen the two allen screws holding the pulley in and it will come out.