ES350 16″ Chain Saw

Experienced gardeners share their insights in answering this question :
There is 1 other 300S model , do not it is significantly different.
http://www.ordertree.com/modelinfo/MCC/300S-14-07%2F93-to-05%2F96-IPL-211789/139.300S-14-07%2F93-to-05%2F96-IPL-211789.1.59.1.html
I recommend you open the attached IPL (300S-14) and use it as a disassembly/reassembly guide. I think the “General Assembly” print has the detail you need. If it were my project I might snap some photos as things progress just to refresh my memory when putting it all back together.

All saws can be found here (Alpha Numeric order; yours – right column about halfway down):
McCulloch IPLs
http://www.ordertree.com/modelinfo/McCulloch/139.59.html

Good Luck. If I be of additional help please reply below. HTH
Lou

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A: The spark plug gap on all products is . 025-inch.
Loosen the guide bar nuts and turn the adjusting screw counter-clockwise 1/4 turn to loosen the chain if it is too tight. Loosen the guide bar nuts and turn the adjusting screw clockwise 1/4 turn to tighten the chain if it is loose.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I was replacing pull cord and the tiny bar which connects the trigger to the carb fell off before I could see how it was installed. I canot figure out how it goes back. It is a Bvm 200 25cc Poulan leaf blower
ANSWER : It should be pretty simple to replace. Would expect the trigger to come out, put the rod/bar on the carb then on the trigger (probably has to swivel the trigger to get the part on) the set trigger back in it’s position. Hope this helps. Easier to do than explain.

Read Full Q/A … : ES350 16″ Chain Saw

Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on

Read Full Q/A … : ES350 16″ Chain Saw

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Read Full Q/A … : ES350 16″ Chain Saw

How do you replace the starter cord on a poulan chain saw
ANSWER : R² Starter Rope by SmallEng.com

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Read Full Q/A … : ES350 16″ Chain Saw

Im replacing the pull cord, i have it apart and all that but which way do i wind the cord??
ANSWER : You always wind the cord counterclockwise even in lawnmover.

Read Full Q/A … : ES350 16″ Chain Saw

Poulan 4018 pp4018 – Poulan P4018 18Inch 40cc 2Cycle Gas Powered Easy Start Chain Saw With Case
ANSWER : Proper fuel mixture?

Read Full Q/A … : ES350 16″ Chain Saw

How do I replace the fuel line for a Poulan ppbp30?
ANSWER : Open the top of the machine to access the carb, Normally it is easily done with needle nose pliers.

Read Full Q/A … : ES350 16″ Chain Saw

Trying to replace the pull cord , can’t get last housing off to get to coile up old cord , the shaft has a nut on the end that the auger screws into but i cannot get that piece off as there is no where to put a wrench to stop the turning of the engine shaft so i can torque the nut in the other direction to get it off , what do i do to get this pull cord replaced?
ANSWER : Use an impact wrench it will hit the nut so fast it will loosen it befroe the engine car turn over

Read Full Q/A … : ES350 16″ Chain Saw