30.1CC Chainsaw With a 14 In.bar and Chain
Experienced gardeners share their insights in answering this question :
Don’t know about your particualr saw, but general instructions are :
take the bar cover off,
take the bar and chain off,
put your piston stop in,
remove the clutch nut by unscrewing it clockwise,
remove the shoes and springs from inside the drum, and pouit them in the new one,
replace it all.
If you don’t have a piston stop you can pull the starter cord all the way out and stuff some of it into the spark plug hole to stop the piston moving when you turn the clutch nut.
take the bar cover off,
take the bar and chain off,
put your piston stop in,
remove the clutch nut by unscrewing it clockwise,
remove the shoes and springs from inside the drum, and pouit them in the new one,
replace it all.
If you don’t have a piston stop you can pull the starter cord all the way out and stuff some of it into the spark plug hole to stop the piston moving when you turn the clutch nut.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Yes, you can use the 16” bar on the 14” chain saw, and visa-versa. Helpful?
Your Echo chainsaw is a two-stroke engine that takes a mixture of unleaded gasoline and two-stroke motor oil at a ration of 50 to 1.
Most chainsaws can operate up to three different bar sizes. Guide bars are measured in length, from the tip of the bar to the heel, and range in size from 14 to over 40 inches. Check the specifications in your model`s operator`s manual to see what size bars you can run on your saw.
Convenience at the touch of a button
A manual fuel pump makes it easier to start STIHL chain saws and power tools and reduces the number of pulls required. Simply press the primer bulb several times before starting.
The fuel and oil mixture should always be 2% (50:1).
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas.
Typically a chainsaw with a shorter bar around 14” and smaller is enough for property maintenance, trimming, pruning, and cutting down broken tree limbs. On the other hand, cutting down small trees, thick branches, and cleaning up storm damage will need a longer bar around 16”-20” to make the job easier and safer.
Not every bar or chain is right for every saw. For example, larger chainsaw bars work best with more powerful saws because it takes more energy to drive a chain around a long bar. That`s why electric saws use bars 18″ and shorter. Similarly, chainsaw chains are measured to fit certain bars.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Echo chainsaw how do you remove the clutch from an ehco cs400evl?
ANSWER : OK I looked at Echousa.com and see that there shoule be a hex nut on the side where the clutch is. It doesn’t specify whether it is left or right hand thread. but what I used to do is we have a plastic plug to put in the cylinder to stop piston from moving and then putting a ratchet on the hex nut. without the plug you can try an impact wrench to BUMP the nut in forward and reverse to remove it. Make sure the switch is off before attempting either action. You can look at the manual or parts explosion at the site I listed
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Chain brake jammed on Echo CS400 chainsaw
ANSWER : You will need to release the brake by applying a very heavy screwdriver to the + shaped part of the brake coupling. Check the action of the brake handle and duplicate it at the the +. Hope this helps!
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Chain not moving on a running chain saw. – Echo 30.1CC Chainsaw With a 14 In.bar and Chain
ANSWER : Hi. Possibly the chain brake is engaged. It is the thing just in front of the forward handle. Try pulling it back, before starting the saw. It should click into place. This device is supposed to stop the chain in the event of a severe kick-back. If that’s not it, you are probably looking at a new clutch or maybe sprocket.
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Cleaning the fuel filter
ANSWER : I would try cleaning the carb. sounds like there is something stuck in the jet to me.
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Cant remove clutch cover – Echo CS400 18" Chain Saw
ANSWER : Is the Chain brake engaged?
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Troubleshooting chainsaw hit some dirt now wont cut and smokes at chain little oil to bar and chain
ANSWER : You need to clean the chainsaw areas where the dirt has gone with a water hose. You may have clogged up the oil thing that puts oil on the chain. Hope this helps! And yes, dirt will make a chain dull. You might have to replace the chain or have it sharpened.
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
Engine smoke when chain brake on
ANSWER : It sounds like the band is too tight and the smoke is coming from a burning clutch. You need to get your owners manual and loosen the band before you burn the parts up.
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
SAW WONT START IT HAS FIRE TO THE PLUG AND IT WONT START WHEN I SHOOT A LITTLE ETHER IN IT
ANSWER : If the engine has good compression, and good spark, it should at least ‘pop’ several times. Check the flywheel ‘key’ as it may have sheared causing the ignition to be out of time. Hope this helps!
Read Full Q/A … : 30.1CC Chainsaw With a 14 In.bar and Chain
