Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Reduce the roller tension until you can press the torch trigger and the rollers slip (wire does not feed) Grip the wire between your thumb and first finger. Your grip should be firm but not tight (no white knuckles please)
If the drive rolls are turning but the wire is not feeding, it is usually caused by inadequate drive roll pressure or a blockage in the contact tip or liner. Check the drive rolls and contact tip before moving on to the liner, which takes more time and effort to check and replace.
Your welding wire not feeding properly off the spool is likely due to incorrect tension on either the spool break, the drive rolls, or both. Too much tension can cause wear on the wire and too little can lead to birdnesting, so it`s important to find the sweet spot on both parts.
The ideal pressure range for most standard MIG welding jobs is between 3 to 8 PSI.
Push or pull: Here the rule is simple. “If it produces slag, you drag,” says Leisner. In other words, you drag the rod or wire when welding with a stick or flux-core wire welder. Otherwise, you push the wire with metal inert gas (MIG) welding.
Wire feed speed/amperage too high: Setting the wire feed speed or amperage too high (depending on what type of machine you`re using) can cause poor arc starts, and lead to an excessively wide weld bead, burn-through, excessive spatter and poor penetration.
Once you get the drive rolls to slip, tighten the drive rolls a half turn more. You can also feed wire into the palm of your welding glove if it is well padded. Just make sure there isn`t a really sharp point by bending the end of the wire over.
The opening roller surface speed is usually selected from within the range 800–2500 m/min, depending on the type of fibre and the roller design.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do I change from vaccum to leaf blower? – Black & Decker & Leaf Hog Blower / Vacuum
ANSWER : You haven’t stated the model you’re referring to.. Here’s a link to a Black and Decker blower vac manual, but it might not be your model as I’m having to guess due to lack of info.http://compsource.manualsonline.com/user-manual/black_decker/blower/bv3600

Read Full Q/A … : Garden

I REQUIRE A USERS MANNUAL FOR A BLACK & DECKER GL 580 LINE TRIMMER. IS THIS INFO AVAILABLE ON LINE?
ANSWER : Yes possibly, but hard to find. I did find the operators manual for a model close to yours. It is right here:
http://www.dewaltservicenet.com/documents/English/Instruction%20Manual/Brazil/GL300%20ty2.pdf

Read Full Q/A … : Garden

How do I get an owners manual for my snowblower Craftsman EZ steer 9.0 28″
ANSWER : Go to the Sears Parts Direct website and enter your model number where it says to. Here’s the link. http://www.searspartsdirect.com/partsdirect/user-manuals

Read Full Q/A … : Garden

Where can I get an owners manual for a troybilt bronco tiller? I think the tiller is 5/6 years old
ANSWER : You should ask the people you bought it from, but if you can’t find them you can look around on the ‘net to find other people with the same machine.

Read Full Q/A … : Garden

Feed rollers wire not feeding thru
ANSWER :

Read Full Q/A … : Garden

I need a owners manual for a pressure wahser GCV 160 from honda
ANSWER : MiTM will have that. See mitm.com Honda makes the motor but not the pressure washer. Honda does have manuals if you need one for that GCV160 motor.

Read Full Q/A … : Garden

How to replace a oiler on a stihl chainsaw ? – Stihl Service Manual for 031AV Chainsaw with Parts List
ANSWER : Remove the worm, sealing ring and washer, loosen the pan head screws on the oil pump and replace. Check if the gasket is re-usable.

Read Full Q/A … : Garden

Where can i get the washer that hold the blade flush to the star-gear under the mower. A flat washer do not work and allows the blade to flop. None of the small engine repair shops care Ariens parts..When I bought the mower I never recieved a owners manual with a parts list who do I contact for one of those too. Thanks for your help, by the way my name is Eric
ANSWER : Get them direct
http://www.ariens.com/corporate/pages/partsradar.aspx

Read Full Q/A … : Garden