25cc Gas Line Trimmer

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Remove the air filter and spray carburetor cleaner into the intake. Let it sit for several minutes to help loosen and dissolve varnish. Replace the filter and try starting the trimmer. If this doesn`t solve the problem, consider disassembling the carburetor to give it a more thorough cleaning.
Turn on the ignition switch and pull the starting cord quickly. You should see a spark in the plug gap. Since the spark may be faint, it may help to do the test in a dark area. If there is no spark, check for a broken or shorted (bare) lead wire or bad switch.
A clogged carburetor is most commonly caused by leaving fuel in the hedge trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall or run roughly.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I need to replace fuel line in Weedeater trimmer. How can I do it ?
ANSWER : Enter Weed Eater fuel lines in the search field for numerous results and if not, repost here.

Read Full Q/A … : 25cc Gas Line Trimmer

My weed eater is leaking gas, and i dunno where from
ANSWER : Your fuel lines are probably old & brittel they are the first thing to leak on those sometimes they leak around the tank but they are really thin lines & they get hot from engine heat & dry rot easly replace both lines from carb to tank & the leak will be gone most lines are 1/4 lines in most cases

Read Full Q/A … : 25cc Gas Line Trimmer

Start but will not keep running – Poulan/Weed Eater No. Te475 952711797 17" Le Gas Trimmer/Edger
ANSWER : Hi rt2714…

Sounds like you have dirt/debris in your carburetor jets,fuel passages or a diaphgram that is becoming non-flexible.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Also check you fuel lines condition after a while they will degrade and need replacment.If you do replace your fuel lines be sure to draw on a piece of paper the routing of the fuel lines for later attachment to the correct connection.
Make sure you are getting spark at the spark plug, to do this:Remove your spark plug and check to be sure you are getting fire at the spark plug.You do this by grounding the plug on the head of the engine and pulling the crank rope, if you are getting spark then:Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of weedeaters.Also make sure you are using fresh fuel…and oil mix if your using a two cycle mower or weedeater with the oil to the right mixture and not too much oil as it can cause hard starting.If the mower/weedeater is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.Sounds like you will need to clean the carburetor or replace your carburetor internal rubber parts like the diaphgram and O rings.I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use compressed air to blow out all the fuel and air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Sometimes you can get by with priming the carburetor or using starting fluid and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their orginal position before you started.Once you have your carburetor rebuilt that should solve your problem.
This is a FREE answer,Please take time to rate me

Read Full Q/A … : 25cc Gas Line Trimmer

The head will not spin on Troy Built weed eatter
ANSWER : Sounds like your flex cable has taken a trip south. Pull the shaft off the head and take a look at the flex cable. If flex cable is ok, they your clutch is defective.

Read Full Q/A … : 25cc Gas Line Trimmer

Weed eater won’t run
ANSWER : Sounds like you may just have a dirty carburetor.Youwill need to disassemble the carburetor and spray with carb.cleaner.Make sure the small screen is free of debris. (Should be able to seedaylight through it.)Use a Den Tek Brush, (http://www.drugstore.com/products/prod.asp?pid=165357&catid=1152),to clean the small portals in carb. These portals can become blocked. Reassemble and start.If the carb. parts are more than 4 years old, you may have to replace them.If you need further assistance, just let me know.Jim

Read Full Q/A … : 25cc Gas Line Trimmer

Need to replace fuel lines on my Troy Bilt gas hedge trimmer. Where can I get replacement fuel lines… or better yet… what size are the lines and where can I buy a few feet of the lines. Note: I have reviewed the parts assembly and it would seem to indicate I have to replace the entire handle assembly (Part #1) instead of just buying replacement hose(s). Any help to resolve my issue would be greatly appreciated and thanks in advance
ANSWER : Replacement fuel lines should be readily available at your local lawnmower repair shop. Your TroyBilt hedger uses fuel line that is 3/32″ (2.4mm) interior dimension, 3/16″ (4.8mm) outside dimension, with a 3/64″ (1.2mm) wall dimension.
Most manufacturers don’t offer replacement line, only fuel tank assemblies. Find your local shop, and try to get the TYGON brand…it is yellow. Tygon lasts the longest. You should be able to buy it by the foot for less than $2 per foot. You will need 2 feet of hose to replace both lines.

Make sure to clean the in-tank filter when replacing hoses.

Good luck.

Read Full Q/A … : 25cc Gas Line Trimmer

Fuel line replacement ?? – Weed Eater Featherlite Fl20 Lawn Edgers
ANSWER : Http://www.ereplacementparts.com/weed-eater-fl20-type-gas-trimmer-parts-c-17589_17626_18076.html

Its a pretty simple process. Here’s the parts list

Read Full Q/A … : 25cc Gas Line Trimmer

Troy built weed eater won’t feed line
ANSWER : Check the size of the line,(OD), make sure you are using the correct size, sometimes cheap line will be problematic, also, you said you are re-stringing it, try a new batch of string, the old string inside the hub can get chaffed and will stick to itself…

Read Full Q/A … : 25cc Gas Line Trimmer