Garden

Experienced gardeners share their insights in answering this question :
Hello ,no search results for that tiller,except e bay,,

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Horse I tillers (serial numbers up to #314150) used two matched drive belts and a fiber reverse disc. These are referred to as “2-Speed” tillers. Horse II (serial number 314151 and higher) tillers used one drive belt and a rubber ringed reverse disc.
It is often beneficial to change the drive belts in your car approximately every 60,000 to 100,000 miles. By undergoing annual car inspections, you can have your drive belts evaluated. If any signs of damage or severe wear and tear are identified, the belts can be replaced.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Drive belt Have replace drive belt but mower still has no forward movement. Mower is only 2 years old but its already had to have another drive belt installed by the dealer last year. wanted to do it myself but when i install belt theres hardly any tension so mower doesnt move. Checked and rechecked the diagram and is installed correctly. Cant find a tensioner adjustment if it has one.
ANSWER : I don’t have an answer for you, but Do you have a diagram of the Drive Belt?

Read Full Q/A … : Garden

Replacing drive and auger belts on a John Deere 1032 snowthrower
ANSWER : You don’t need to remove the any lever linkages but you will need to remove some of the pulleys.If you can give an exact model number of the tractor it would help.

Read Full Q/A … : Garden

How to change drive belt – Huskee Tractor Replacement Riding Lawn Mower 42" Deck Mulching Kit fits Huske
ANSWER : Step 1 – Loosen tension and remove belt. Locate the adjustment fastener and loosen it. …
Step 2 – Inspect drive and drive pulleys. Check the drive and pulley wheels. …
Step 3 – Select correct replacement belt. …
Step 4 – Install V-belt. …
Step 5 – Correctly tension new belt. …
Step 6 – Start the engine.

Read Full Q/A … : Garden

Diagram for belt replacement on 1988 Toyota Tercel
ANSWER : Fig. 1: Correct timing mark placement on 3E and 3E-E enginesHope this helps; also keep in mind that your
feedback is important and I`ll appreciate your time and consideration if
you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Read Full Q/A … : Garden

How to replace belt on 1992 toyota carolla station wagon
ANSWER : Http://www.2carpros.com/diagrams/toyota/corolla/1992 click on link.

Read Full Q/A … : Garden

KEEPS BURNING UP FORWARD BELTS EVERY 4HRS OF RUN TIME AND I DO HAVE CORRECT SIZE
ANSWER : Driving wheles for belts is not in line

Read Full Q/A … : Garden

My mower blades disengage when operating.
ANSWER : Not sure of your question, but if you mean, they start when you flip the switch and then disengage but the switch stays up.. you need to check two things. (1) The out put of your alternator, read the battery with a volt meter before you start it, then start up the engine and read the voltage again should be a higher reading with the engine running. 12.4 vdc with the engine off – 13.7 vdc with it running. (just an example). Next will be your seat switch.There is a switch under the seat if you are not sitting in the seat the blades should turn off. so the switch could be out of its socket, or broken.

Read Full Q/A … : Garden

Mantiss tiller Model 20–1992, The drive gear has woren out and I want to replace it. The transmission housing is one piece-except for the cover. How do you dismantle it?———-help!——–Gary
ANSWER : Remove cover and place transmission in a vice.Turn tine shaft by hand.Then remove the worn gear.1-800-366-6268.This number is to Mantis.

Read Full Q/A … : Garden