Garden
Experienced gardeners share their insights in answering this question :
I assume you have the Ryobi powerhead with the multiple tool shaft (can use it with an edger, blower, trimmer, and pole saw) If so, does the powerhead square drive spin when you squeeze the throttle trigger? Does the chain move freely on the saw end when not connected? Is the attachment fully inserted into the powerhead shaft (small spring-loaded button should pop out of the hole when fully inserted.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood. If the chain is too tight, the chain may not rotate at the proper speed, causing the chain not to cut properly. To adjust the chain, tighten or loosen the adjustment screw.
Check your battery`s charge level indicator, ensure the battery is fully charged. Check the battery is seated correctly in the tool. Make sure the battery isn`t hot. RYOBI batteries have overheat protection built into them.
When you go to operate the saw, and the saw does not operate, you might want to check out a few things: 1) Make sure the battery is fully charged. 2) Be sure that the battery is put into the saw correctly, and secured. 3) There might be debris on the battery, or inside the saw, where the battery connects.
There are three main reasons for a chain to come off: Incorrect bar and/or chain for the saw; check to be sure that you are using the proper chain pitch, gauge and number of drive links to match the guide bar. Chain not properly tensioned; It is normal for a new chain to stretch and require frequent adjustment.
Keeping the Ryobi Pole Saw Lubricated
You don`t need Ryobi specific oil. You can use any quality bar and chain oil to keep your pole saw running.
Your pole saw blade may not rotate if the chain is tensioned too tight. When the pole saw is not being used, the chain should sit on the bar fairly snugly, so that when pulled, it will raise around ¼- ½ an inch off of the bar. A chain that is too tight can cause damage to the crankshaft or other associated parts.
Keeping the Ryobi Pole Saw Lubricated
You don`t need Ryobi specific oil. You can use any quality bar and chain oil to keep your pole saw running.
The air filter may be clogged. If the air filter is clogged, the engine will get too much fuel and not enough air. As a result, the engine may stall. If the air filter is clogged, replace it.
The air filter may be clogged. If the air filter is clogged, the engine will get too much fuel and not enough air. As a result, the engine may stall. If the air filter is clogged, replace it.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
My Ryobi portable table saw BTS20 just quit working in the middle of a cut.
ANSWER : Me id look at the under side of saw , id bet the saw just tripped out in use and needs to be reset , id also bet the reset is marked in red some place around motor
Read Full Q/A … : Garden
Ryobi PCN 4545 starts perfectly but chain will not turn.
Can you help?
Can you help?
ANSWER : Hi, have you released the chainbrake? Regards Phil.
Read Full Q/A … : Garden
WHAT OIL DO I USE IN ELECTRIC REMMINGTON POLE SAW?
ANSWER : Bar oil–home centers, Walmart, saw dealers.
Read Full Q/A … : Garden
Lost oil cap and bulb
ANSWER : Remmington’s parts department.
Read Full Q/A … : Garden
I have just bought a petrol chainsaw from ryobi but I can’t make the engine start with the rip chord. I have followed the instructions but no luck. The engine does not even turn over.
ANSWER : Check to see if the brake is on. the large handle in front. move it. its a safety device that stops the saw if it kicks back on you.
Read Full Q/A … : Garden
Where do I buy Pole saw parts – Remington Electric Pole Saw
ANSWER : Call 1-800-654-8534
Read Full Q/A … : Garden
Im having trouble starting my 2 stroke chainsaw. I follow the instructions but it wont fire over it sounds like its just about to but wont.
ANSWER : Here is a Link to one of my Tips:http://www.fixya.com/support/r6081405-cleaning_small_engie_carburetorGood Luck!Jim
Read Full Q/A … : Garden
Saw just stop working doesn’t come on check switch looks good. have move then one saw and 2 have just stop running after a while of cutting. Neither where over heated. I have 3 saws 16″ 14″ and pole is the switch the same in all three brfore I take the working one apart. Help.
ANSWER : Did you try them directly in the outlet or with a different extension cord? Have you checked the outlet for the correct power? Did you try a different outlet? Provide model numbers for the bad saws and I will provide an IPL with switch part numbers. Reply below.
Lou
Are you aware RemingtonPower is no longer in production?
Lou
Are you aware RemingtonPower is no longer in production?
Read Full Q/A … : Garden
