Garden
Experienced gardeners share their insights in answering this question :
Hi tbonner1…
*****************************************************************************************************************************************************************Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line condition after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of blowers.When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor or take a picture for later reference.Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.Make sure you are using fresh fuel…and oil if your using a two cycle blower with the oil to the right mixture…too much oil as it can cause hard starting and excessive smoking.If the blower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Note:The little spring inside of the carburetor goes under the float arm.That is where your fuel inlet needle/float valve is located…on the arm at the end.Normally there is a small indetion in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me thumbs up
*****************************************************************************************************************************************************************Sounds like you have dirt/debris in your caburetor jets,fuel passages or a diaphgram that is becoming non-flexible. Check/Clean/Replace your Air Filter, a dirty air filter can make your engine run to rich with fuel.
Note: ALWAYS USE COMPRESSED AIR TO CLEAN YOUR JETS AND PASSAGES, VERY IMPORTANT.
Note:Before you disassemble the carburetor:Write down on a piece of paper or take a picture of how the linkage attaches to your carburetor for later reference when you go to reinstall your carburetor.Mark each piece with a awl, or some kind of instrument that will make an alignment scratch before you disassemble the carburetor into separate pieces.That way you will know which way it goes back together when you reassemble it.
Sometimes you can get by with priming the carburetor or by using a very small shot of starting fluid and letting it run a few times like that, and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Be sure to check your fuel tank for water and dirt/debris, if there is water/debris then you need to clean your tank.Check you fuel line condition after a while they will degrade and need replacement.
Check/Clean/Replace your fuel filter if you have one, normally they are located in the fuel tank of blowers.When you remove your fuel lines from the carburetor be sure to make a drawing to how the lines are connected to the carburetor or take a picture for later reference.Normally the big line will be the line the fuel filter is connected to inside of the tank.The smaller of the two lines is the return to the fuel tank from the carburetor after it is pumped thru the carburetor by the primer bulb.Make sure you are using fresh fuel…and oil if your using a two cycle blower with the oil to the right mixture…too much oil as it can cause hard starting and excessive smoking.If the blower is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.The diaphgram may look good and flexible, but it can be deceiving and not act as a fuel pump as it should because it has become too hard and will cause hard starting,start and run and shut off, etc.
When you clean your carburetor, I recommend that you use a laquer thinner type cleaner to clean and dissolve the laquer build-up in the float and needle jet passages.Be sure to remove all plastic and rubber parts before using the laquer thinner because it can dissolve the plastic parts and render them unuseable.Be sure to use COMPRESSED AIR to blow out all the fuel and air passages.The higher air pressure is needed to blow some of the trash/debris from the fuel or air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Keep in mind that the float (if you have one) for the carburetor must be level when you go to reassemble the carburetor or follow the instructions you get with the carburetor kit, or you could also ask the parts man that you get your kit from.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their original position before you started.Note:The little spring inside of the carburetor goes under the float arm.That is where your fuel inlet needle/float valve is located…on the arm at the end.Normally there is a small indetion in the carburetor base and a small protrusion on the underneath of the float arm where the spring will be in the right postion for installation.The spring will set in the indention and you will install the float arm with the needle/float valve and float rod into position over top of the spring,you will push down until it is in position and then you can tighten the screw that holds the float arm assembly in position.Once you have your carburetor cleaned/rebuilt that should solve your problem.Please take time to rate me thumbs up
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Many times this is caused by a plugged vent in the gas cap. Try running it and unscrew the fuel cap part way to see if venting the tank will allow it to run without the choke. If so, then clean the cap with hot water and dish soap or replace the cap with a new one.
Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the engine may stall. To unclog the spark arrestor, remove it and clean it with a wire brush. You may also replace the spark arrestor.
Details. Why would the engine only run while the choke is on or with repeated manual priming? An engine that requires the choking (partial or full) after initial engine warm up is an indication that the engine fuel air mixture system is out of adjustment.
An engine that will fire and run with the choke closed but dies when the choke is opened likely has debris at least partially blocking the fuel passages in the carburetor. In this condition the closed choke provides enough extra fuel to enter the engine to overcome the lack of fuel flowing through the other passages.
Positive-displacement blowers provide a constant volume of air even if the system pressure varies. They are especially suitable for applications prone to clogging, since they can produce enough pres- sure – typically up to 1.25 kg/cm2 – to blow clogged materials free.
Maintenance of gas powered leaf blowers produces toxic waste like fuel filters and contaminated air filters. Blowers erode, compact and dry out soil and harm plants, microorganisms and pollinators.
An engine needs more air as it warms up, so the choke needs to open to allow more air. With a manual choke, you will need to close and open the choke yourself when starting your engine, while an electric choke will control the air supply itself when the engine is started.
If your carburetor is clogged, it can cause your leaf blower`s engine to die when the choke is disengaged. You can disassemble it, clean it, and replace individual parts with a carb kit. Once your carburetor has been unclogged, cleaned, and re-assembled using the carb kit, the engine should run with the choke off.
Turn on the ignition of your car. Once the engine is warm, you can remove the air filter and check whether the choke is open or closed. At this point, the choke should be open to allow the engine to breathe fully.
If your bike is only running with the choke on, it`s probably because it`s running too lean. This can be caused by a few different things: All internal combustion engines need three things to run: fuel, air, and spark. If any of these are missing or not working properly, the engine won`t run.
It will not damage the engine at all. All that will happen is that it will run richer, thus using more fuel. If you did it for thousands of miles you`d probably end up with more deposits in the engine/exhaust, but even that is easy to sort.
Why Does Your Lawn Mower Only Run With Choke On? Your lawn mower only runs with choke on because of a problem with the engine fuel-air mixture system, which can be caused by the carburetor, bad fuel, or air leaks. The choke compels more fuel in the combustion chamber to help the engine to turn over when cold.
It will not damage the engine at all. All that will happen is that it will run richer, thus using more fuel. If you did it for thousands of miles you`d probably end up with more deposits in the engine/exhaust, but even that is easy to sort.
Why Does Your Lawn Mower Only Run With Choke On? Your lawn mower only runs with choke on because of a problem with the engine fuel-air mixture system, which can be caused by the carburetor, bad fuel, or air leaks. The choke compels more fuel in the combustion chamber to help the engine to turn over when cold.
A choke valve/cable is designed to restrict the flow of air in the carburettor of an engine. This helps enrich the fuel-air mixture, improving the ability to start an engine in low temperature conditions.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Seems to start easily run for a few minutes and then slow and stop–bulb remains full –gas is good–have tried half choke in case too lean–did not solve–also seems possibly related to the angle I hold it at–seems to cut out quicker if blower tube angled more downward.
ANSWER : Your filter may be hanging up in the tank. you also my be losing compression
Read Full Q/A … : Garden
Want run unless choke remains on – Stihl Bg72 Leaf Blower Intake
ANSWER : Probably fuel starvation.Wrong fuel air mix settings on the carb. Damaged carb diaphragm.
Read Full Q/A … : Garden
Will only develop power (and run somewhat properly) when the choke is engaged about 90%. Starts fine.
ANSWER : Sounds to me as tho you may have a loose carburetor or another part that is letting air into the system. Check all bolts and screws for tightness. Also, you may need to clean the carburetor or put some cleaner in your gas. Not too much, only about a tablespoon, but check the screws/bolts first.
Read Full Q/A … : Garden
Have to run on half choke,just stops if i turn it off.fuel is 25 to 1. thanks alan.
ANSWER : More than likely a small passage way in the carb is clogged. You can try some carb cleaner, but you may need to disassemble the carb and clean it out. Be advised that these passageways are sometimes as fine as a human hair, and almost impossible to clear sometimes. A new carb may be required if it is worth it to you. Sorry.
Read Full Q/A … : Garden
Echo pb500 only runs with choke open – Echo Gas Blower 162 MPH 450 CFM Blower PB500T
ANSWER : I’m not to sure about the question. But you say it runs with the chock open. Your engine will only run with the chock open. Can you clarify?
Read Full Q/A … : Garden
While running what setting does the choke lever need to be placed in
ANSWER : Depending on how your unit runs, it may need to be on half choke until the motor warms up. After the motor gets hot it should run with the choke fully off.
Read Full Q/A … : Garden
Blower only runs with full choke. When I switch to half choke, it dies and won’t start.
ANSWER : It may simply need the high speed jet opening up a bit (2 screws near eachother on the carb and the high speed is furthest from the engine)failing that it needs a carb kit…. this is a serviceable item changed regularly.
Read Full Q/A … : Garden
My blower only runs with 3/4 choke even after warm up.
ANSWER : Look on the carb for 2 screws side by side. where those screws go into the carb, it will be stamped with an “H” and “L”. Open the screw that is next to the “H”, counterclockwise about 1/4 turn at a time with the engine running, that should solve it.
Read Full Q/A … : Garden
