Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
These can easily be replaced, saving you the cost of a new pump. However, major leaks such as the ones caused by cracked or damaged plungers, can lead to pump failures. Plungers can be repaired or replaced, but the cost should be considered.
No, not all pressure washer accessories are universal, nor are they always interchangeable. Accessories may differ in fittings from one machine to another and may not fit together correctly. Some pressure washers are also brand-specific, meaning they will only work with accessories from the same manufacturer.
Pressure washer water pumps need relatively low oil recommended by the manufacturer, as specified in the owner`s manual. (Purchase pre-measured bottles of pump oil for water pumps without dipsticks.) Never use special oil additives or detergents, unless specified in the owner`s manual.
AAA Industries is part of FNA Group, so you may see AAA pumps for power washers listed under the Comet and OEM Industries, LTD. brands.
Pump repair is necessary to reduce the operating costs of pumping and to prevent corrosion in the pumps. Pump repair may be performed when there are changes in sound of a running pump, abrupt changes in bearing temperatures, and seal chamber leakage of a pump.
In nearly all instances, pump failure is the result of improper installation or operation rather than normal wear. One of the most common causes of pump failure is improper or unnecessary service, often as a result of the operator attempting the service.
If you have a pressure washer or are considering buying one, you`ve probably noticed that there are all kinds of pressure washer nozzles to choose from. Nozzles are color-coded to make it easy to choose the one that you need, and the colors are universal.
Professional pressure washers will have triplex or belt drive pumps, and entry-level gas pressure washers will have axial pumps. On the flip side, most entry-level electric pressure washers have wobble pumps, which are not replaceable, and in those cases, you`re better off buying a whole new unit.
Most pressure washer pumps use a 30w non-detergent oil. This is because most pressure washer pumps use splash lubrication. This is a process that includes rotating “dippers” that throw oil into the pistons and cylinders.
Experts advise doing an initial oil change after the first 50 hours of pump use. After that, change the crankcase oil every 3 months or after every 500 hours of operation, whichever comes first. High pressure plunger pumps require a specially formulated oil; otherwise regular pump oil is appropriate.
If an engine`s water pump is failing, there are two replacement options to consider: a rebuilt/remanufactured water pump or a brand-new one. Before choosing, it`s important to weigh the pros and cons of each option.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a 1/2 horse wayne shallow well pump. At times the water in the house slows to a trickel. This will happen for about 40-120 seconds then the pump seems to kick on and the pressure is restored. I have replaced the high low switch and the problem persists. Please let me know any thoughts on the problem. Thank You
ANSWER : Check air in your water tank should be less than you’re cut in pressure..
Read Full Q/A … : Garden
1999 ford expiodition
ANSWER : Use a pressure gauge to check pressure at the rail. Change fuel filter. Replace fuel pump if needed.
Read Full Q/A … : Garden
We have a Flotec 3/4 HP submersible pump, it was already here when we moved in, we have lived here for 3 yrs, so we dont know how old it is. After living here for 2 yrs, it started to get very noisy, like a groaning noise. We replaced it w/ a l/2 HP Wayne(our mistake) We got water in the basement b/c the wayne pump quit running. We put the Flotec back on. Trying to find a replacement, but stores are all out. Question is, do you think we can rely on the Flotec that is making the strange noises? Thanks, Chris
ANSWER : Take strainer off to see if fravel stucj. if not, motor bearing may be shot. I would replace. I like wayne.
Read Full Q/A … : Garden
I have a 1 hp in ground Flotec pool pump. It is not pumping the proper flo. It makes noise when it starts but then clears up. The motor sounds good. How do I get a manual on the parts for the pump itself. Frank Dedman
ANSWER : GOOD LUCK GETTING PARTS FOR THIS.. FRANK , IF WERE MY POOL I WOULD CHANGE THAT PUMP OUT TO A STA-RITE DURA GLASS.. FLOTEC IS A POOR COPY OF THE STA RITE.. OR YOU CAN CHECK THE IMPELLER IF IT IS PLUGGED WITH TRASH OR IT COULD HAVE A BAD CAPACITOR.. BRING IT IN AND HAVE IT CHECKED..
Read Full Q/A … : Garden
I have a Utilitech brand one-horse motor convertible jet pump. The pump is running, and I’m down 43 feet to the bottom of my well. From the top to the water level is 32 feet, and I have 11 feet of water. When it’s not pumping, it sits at 20 PSI When it’s pumping water, it sits at 11 PSI. But then just pumps for appr. 10 minutes, and then shuts off. I can wait awhile & pick the pipe up and down, and it starts pumping again. Then I shut the faucet off and it goes back up to 20 PSI. Then I turn it on & drops down to 11 PSI. I do not lose my prime, and I have no leaks. This is a brand new pump. \r\n I had a 1/2 horsepower pump for several years, and just replaced it with this one horsepower pump, and I can’t get it to work right. When it’s pumping water, it pumps at 11 PSI. I have my foot valve at 4 1/2 feet from the bottom.
ANSWER :
Read Full Q/A … : Garden
Sump pump hums and then kicks breaker. Will not pump. I cleaned everything, still have problem
ANSWER : Pump motor is jammed causing overload and resulting breaker trip. Try to turn the pump shaft by hand, it should be very easy to turn. If there’s any resistance check for blockage.
Read Full Q/A … : Garden
I have Remington REM55PV heater. It starts just fine but when I take finger off ignition button, heater won’t stay running.
ANSWER :
Read Full Q/A … : Garden
I am in the need of the attachmnent for the
ANSWER :
Read Full Q/A … : Garden
