art and run but only for a few seconds then it dies.
Experienced gardeners share their insights in answering this question :
It sounds like a small piece of dirt is in the main jet of the carb assuming you have good spark. you may need to remove the carb and clean it. if it has a float then the needle may be sticking especially if it had older gas in it over the winter as it gets thick and plugs up the fuel passages. good luck.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged.
The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.
In the case that your chainsaw runs for a while, then dies, it may be possible to simply clean the air filter to correct this symptom. However, a damaged air filter should be replaced. Regular checks of the air filter for buildup should be part of your regular chainsaw maintenance routine.
If your chainsaw engine dies at full throttle, check the following parts: the carburetor, fuel lines, fuel filter, air filter, and muffler. Our repair guide can help you identify the right part to stop your chainsaw`s engine from dying at full throttle.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
There is no real set time or length on a chainsaw lifespan. It ultimately comes down to the factors listed above (especially maintenance). That being said, you can expect a quality chainsaw to last you at least 10 years or more.
There could be various causes: incorrect fuel mixture, carburation not calibrated properly, or a wet spark plug. In spite of their power and robustness, chainsaws are actually rather delicate machines that require careful and precise maintenance at every stage of their life cycle.
Because the air doesn`t enter the engine in a controlled or consistent manner, it will cause the RPMs to surge up and down depending on how lean the mixture is at any given moment. This can cause serious engine damage because of a lack of lubrication.
Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised. Cutting a thick wood or timber while running at a low speed or throttle can cause the blades of the chainsaw to become dull.
Fuel Filter is Clogged
When it`s clogged, this affects the flow of gasoline to the engine which then causes the engine to stall. The fuel filter will need replacing if it appears to be clogged yet if it seems clean, it may be a different problem causing the engine to cut out.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Cannot get the saw started – Husqvarna 450 e-series 18" Chain Saw
Check for spark check fuel filter carb kit if sitting for while new plug
Saw runs fine for about 15 minutes,then the idle speeds up,then it dies,almost like it is flooding
Do aclean or overhaul of all fuel components.Change the spark plug or the coil aka=spark plug cable.But if your saw in lees the 2 yrs you need to follow the starting guide in order to avoid flooding.If you need more help come back.Post / thumbs / testimonial are welcome!
Husqvarna 235 is not oiling.Hole and groove on bar have been cleaned. The saw does drip oil with the bar off when running.All parts are clean but bar is not getting oil.Hope you can help,thanks.
With saw running and high speed hold saw close to a piece of wood and check for oiling. If still no oil, then use air pressure at hole in bar to clear.
I used my brand new Husqvarna chain saw for about 30 minutes then when I pinched the blade a little bit and it kicked back out at me, the chain stopped moving. I can’t even turn it by hand. The engine runs but you can tell it run wide open. and the gear that runs the chain doesn’t move either. Please help.
The chainbrake has actuated, you need to pull the hand gurd fully toward the rear of the machine until you hear the click of the brake unloading.
Chain saw starts fine, idles fine, and powers up fine when not cutting a long how when starting to cut a log it bogs down and dies. Does anyone know how to fix this problem or what’s wrong with the chain saw?
Two things that can cause this problem. 1. Your carburetor is not set properly and is not letting the engine get enough fuel under a load. 2. Your chain is binding when you put the chain bar down on the log. Make sure your front chain sproket is turning free and is not too sloppy.
It’s brand new, when I finally get it started it will run good for about 1 min. or less, and then it dies. I pull the choke out all the way, pull it a couple of times, push it half way in, it starts but it’s like it doesn’t have the power to turn the chain, bogging out and then it dies, I will never buy another homelite product, or recommend anyone else to, this is my second one, the first one leaked gas, Home Depot really should quit selling them, there making you look bad too!!
Hi paulbonser… Set your point gap to .20 using a feeler gauge… You can also use a paper matchbook cover, it ia approx. .20 to set the gap on the points. Please take time tor rate me
Husqvarna Model 136 chainsaw will only run for a short time with choke closed. Engine quits shortly after choke is opened.
Take apart the fueling system and carb. Something is blocking or gummed up. One thing that sometimes works is to remove air filter, rev the unit up, and place hand fully over the intake, and remove before unit stalls. This sometimes will clear the blockage.
I have a Pouan Pro. I can start it but then when I give it gas it seems to have no power. It doesn’t die, just gets no power. Occasionally it revs.
It may well be running too rich because the air filter is blocked, remove the filter and just try the revs again free running, if ok, clean/replace the filter.