put a wrench on the to of the spindle (were the grease fitting is locate) I feared that would cause me a problem.
EZ4824 24 hp 48″ Zero Turn Lawn Mower

Experienced gardeners share their insights in answering this question :
If you take them off with a air impact thats what i use or you can put a wrench on the pulley to hold it

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Husqvarna zero turn mowers usually have a model number decal clearly visible on the sides of the frame. The Husqvarna model number, part number, and serial number tag can be located on the frame near the left rear wheel. The model number tag can also be located on the inner frame near the right wheel fender.
Designed for homeowner use all year, this 48-inch Husqvarna riding mower is ideal for mowing yards that are 2 to 3 acres. This ride on mower has a 24-HP Kohler V-Twin engine to deliver powerful performance.
Husqvarna Self-Propelled Push Mower with 5.5 HP Honda OHC Engine, 21in. Cutting Width.
A bypass lever is located on the back of the frame, pull out on the lever to move the mower and push it back in before mowing.
Husqvarna Garden Tractors Powered by Kawasaki

Thanks to a wide range of attachments and a built-in choice of cutting methods a Husqvarna Garden Tractor offers great usability and becomes a powerful partner in your garden all year round.

Husqvarna Zero-Turn Mower —22 HP Briggs & Stratton Endurance Engine, 42in.
This 46-inch Husqvarna lawn tractor comes with a 2-cylinder Kawasaki engine with an automatic drive system and electric PTO.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a husqvarna 5223 zero turn. I cannot get the spindles to ‘bind’ up enough that I can get the blades off. They just spin on me. Can I put a wrench on the to of the spindle (were the grease fitting is locate) I feared that would cause me a problem.
ANSWER : If you take them off with a air impact thats what i use or you can put a wrench on the pulley to hold it

Power to turn the blades is intermitent. What should I look for?
ANSWER : Loose connection, corrosion on connections. If this machine is new to you, do you have to have the brake or clutch on to activate the blades? I would lean towards wires/connections as the cause of your intermittent problem.

How do i change blades on the husqvarna zero turn mower model number LZ6127
ANSWER : Jack up your machine safely and unscrew the bolts holding the blades on..then reverse this order..

I have a husqvarna zero turn rz4623 that will not start.
ANSWER : Give me an idea of what goes on when you turn the Key I have the same mower

I need a blade spindel for my husqvarna ZTR DOES IT COME TOTALLY ASSEMBELED and one new blade model #968999155
ANSWER : Hi , Wow glad I don’t own one of these The spindle completely assembled is part 539104403- 138.37 or bearings #539102677- 67.59 or shaft 539104402- 33.14 all available at /www.sepw.com/ hope this helps.

My Z5426 won’t start. When I pull out the choke and turn the key, gas starts leaking out of the exhaust system just before it gets to the muffler. Last time it did start, it ran really rough. So, I turn off the engine and then tried to restart and that’s when I noticed the fuel leak.
ANSWER : Maybe bad fuel, fuel line leaking, flooding of the carburetor, since it did start and ran rough I am assuming that the gas was left set and more then likely this gummed up the carburetor, you will have to clean/rebuild it. If you have a can of carburetor clean you may be able to spray that into there and clean it up, I would not choke it to start it as it sounds like it got/is flooded/ing. Good Luck Tim

How to get the blade pulley off a zero turn mower
ANSWER : I need to change the pulley on my husqvarna

Exmark 44 Mower bogs down going forward
ANSWER : When you say ‘going forwaed’, is that while mowing or does it do it without the blades engaged or ‘not mowing’?