. Is this system rebuildable? Is there a rebuild kit available for the pump and or motor?
1 HP Submersible Well Pump High Volume ()

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

(insert photo) 1 HP equals 750 Watts.
1 HP Single Phase Open Well Submersible Pumps, Discharge Outlet Size: 30 mm, Capacity: 350 Lph.
1 HP Submersible Pump, Maximum Discharge Flow: 100 – 500 LPM, Maximum Head: 51 to 100 m.
Specifications power rating: 1 HP; head: 3 to 32 meters; capacity: 3100 to 500 LPH.
A power level of 1 hp in submersible water pumps is approximately equivalent to 746 watts (W) or 0.746 kilowatts (kW).
1 HP Single Phase Submersible Pump, Maximum Discharge Flow (LPM): 100 – 500 LPM.
1 HP Single Phase Submersible Pump, Maximum Discharge Flow (LPM): 100 – 500 LPM.
In the case of a 1 HP standard submersible well pump; a 3-4 KW generator is required for the well pump to be able to start, even though 1 KW is the amount of power the pump uses when it is running.
1 HP 32 Stage CRI V3 Submersible Pump Set with Control Panel – Max 270 Ft Depth – Single Phase.
In the case of a 1 HP standard submersible well pump; a 3-4 KW generator is required for the well pump to be able to start, even though 1 KW is the amount of power the pump uses when it is running.
Asian Pumps & Machineries 2hp 1500W Sewage Submersible Water Pump SINGLE PHASE, 30000Lph, 100% COPPER, 10m Cable, Head 15 mtr, Pipe Size 50mm Dewatering Pump.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My Sump Pump is running and wont stop. It usually go for like 30 seconds a few times per day, but it wont stop. I unplugged it and waited 30 secs, plugged it back in and it’s still going.

Any suggestions?

ANSWER : Check your float and the switch. It sound like it is just sticking. If it were bad the pump probally would not start

We have a Flotec 3/4 HP submersible pump, it was already here when we moved in, we have lived here for 3 yrs, so we dont know how old it is. After living here for 2 yrs, it started to get very noisy, like a groaning noise. We replaced it w/ a l/2 HP Wayne(our mistake) We got water in the basement b/c the wayne pump quit running. We put the Flotec back on. Trying to find a replacement, but stores are all out. Question is, do you think we can rely on the Flotec that is making the strange noises? Thanks, Chris
ANSWER : Take strainer off to see if fravel stucj. if not, motor bearing may be shot. I would replace. I like wayne.

Running pump stopped
ANSWER : I assume that the plug in is working properly. Always check power supply first. Is there a GFCI circuit that it is plugged into. Then check the pump to make certain it us turning. How long had it been on before unplugging it. It could be worn out. Sometimes it takes a jolt to start the motor again. How big is the motor. Possible bad capacitor. Could be a solid state motor, then it’s bad. Is it a magnetic motor, that could be turning the wrong way.

Pump works for about 20 seconds then stops for 40 seconds then starts again.
ANSWER : This sounds as if motor is overheating and the thermal switch is stopping it (why it restarts by itself) if a pump is overheating then a few reasons need be looked at , is pump encountering higher viscosity’s than designed for and is having trouble moving liquid fast enough , is distance pump has to lift liquid over what it’s designed to do most of these pumps use liquid it’s moving to provide cooling to pump , is liquid it’s moving warm/Hot allready if so use different type of pump (non submerged) and last but not least is pump worn out and is failing moving parts wearing together make heat !!! ?

Submersible well pump poping breaker
ANSWER : Hi,
The motor is locked and you cannot reverse it… the pump will need to be pulled and replaced…

Replace it with a “sandhandler” type pump that will pump the grit through it with out hurting it..

heatman101

Pump runs for a few minutes becomes hot and stops then starts again
ANSWER : Pump motor is overheating or drawing too much current and the safety is shutting the motor down. After a period, it automatically kicks back in (quite common). Replace motor (and safety which probably comes with, or is actually contained inside motor).

:o).

Sump pump hums and then kicks breaker. Will not pump. I cleaned everything, still have problem
ANSWER : Pump motor is jammed causing overload and resulting breaker trip. Try to turn the pump shaft by hand, it should be very easy to turn. If there’s any resistance check for blockage.

Can the reduce the discharge size of the pump (4 feet away) to have attached to my 3/4″ garden hose?
ANSWER : Possible,but i woudnt recomend it you are likely to overload the motor and damage it