Garden
Experienced gardeners share their insights in answering this question :
Look in the lights and see if there are starters in them,they are either metal or plastic,(they will be round) and are about 1 inch long and about 3/4 inch wide,if so they maybe bad,to remove push in and turn,you can get replacements at any hardware store,or the wall swtch is bad,or are they on a seperate breaker?
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). Check for power first… then the starter (if applicable) and then the bulbs. When all else fails, the ballast should be replaced.
First, this sort of problem is often a broken lampholder (“tombstone”), or failing to get the bulb to seat correctly. The tubes have little “tick” marks molded into the metal end caps to help you see when the pins are square-on engaged. However it is also possible for a ballast to be broken.
The reasons for this can vary considerably from the power source to the bulb itself. Reasons often include a faulty power supply, loose connections, a faulty circuit design, or even damage due to water ingress caused by rain.
Usually. Almost all lighting fixtures can house LED bulbs. To confirm that LED bulbs can be housed in a fluorescent lighting fixture, look for LED bulbs that are “ballast compatible,” this means that they can work with the ballasts that are already installed in your current lighting fixture.
Check the Ballast with a Multimeter
Insert one probe into the wire connector while holding the white wires together. Touch the other probe to the ends of yellow, red, and blue wires coming from the ballast. Some might exclude the yellow. If the ballast doesn`t cause the needle to move, you know it needs to be replaced.
A fluorescent lamp tube is filled with a mix of argon, xenon, neon, or krypton, and mercury vapor.
Most people cannot notice the flicker in fluorescent lights that have a flicker rate of 120 cycles per second (or 120 Hz). Flicker with LED lights may be more noticeable due to the fact that LED lights flicker between less than 10% and 100%, where as fluorescent lights dim to about 35% and back to 100%).
By far the most common problem is a loose wire connection at the switch itself, which is subject to constant on-off usage. Less commonly, a light bulb socket may go bad. If so, you will need to replace the socket.
Check the Circuit Breaker; Shut Off Power
A switch circuit that doesn`t operate correctly may simply have a tripped breaker or blown fuse. Head to the electrical service panel and locate the breaker or fuse. If the breaker is tripped, reset it; or if the fuse is blown, replace it with an exact duplicate.
The two different technologies are entirely different methods of producing light. Fluorescent bulbs contain inert gas within the glass casing while LEDs are a solid state technology. Fluorescent lights produce UV radiation and then convert it into visible light through the use of a phosphor coating inside the bulb.
Compared to fluorescent bulbs, LED lights are up to 80% more efficient. Unlike fluorescent lights, LED lights convert 95% of their energy into light and only 5% is wasted as heat; this is all while still using far less power to provide a strong and consistent output at a lower wattage.
Lamp blinks: This is usually because of a poor connection where the tube fits into its sockets at each end. Take the tube out and clean the pins at each end with fine steel wool. Brush dust out of sockets, then reseat firmly.
Parts cost on average $192.87 – $235.73, and services cost $106.20 – $129.80. This repair takes on average 0.90h – 1.10h for a mechanic to complete.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How do you replace primer bulb on ryobi chainsaw
ANSWER : Https://www.youtube.com/results?search_query=Ryobi+18%22+Chain+Saw+primer+replacement
Ryobi 18 Chain Saw primer replacement YouTube
Read Full Q/A … : Garden
Primer wont work fs45
ANSWER : Rebuild carb
Read Full Q/A … : Garden
Need to replace primer bulb and fuel lines, is there a digram that shows the connections?
ANSWER : Http://www.ereplacementparts.com/images/fuel_line_diagram.jpg
Read Full Q/A … : Garden
How can I repair brake lights?
ANSWER : If all 3 are not working and it isn’t the fuse then I would check out the switch.
Read Full Q/A … : Garden
Why won’t the Prime bulb fill on blower and how to fix?
ANSWER : YOU HAVE THE PRIMER BULB HOOK UP WRONG TRY CHANGING THE FUEL LINES
Read Full Q/A … : Garden
What else should i try
ANSWER : Make sure lines are connected correctly. On the back of primer it is stamped In & out
Read Full Q/A … : Garden
My ballast making a humming noise but will not light up my 600w hps bulb?? small bit of purple light in the bulb when turned on but not lighting up?? tried a 400w bulb in hood with the 6oow ballast and that lights up fine but bulbs going far 2 hot. why wont it fire up my 600w bulb??
ANSWER : NANOLUX BALLAST 400W-1000W NANOLUX HPS and MH electronic ballasts can be light upE-MAIL :[email protected]:sznumberballastNANOLUX HPS and MH electronic ballasts can be light up
Read Full Q/A … : Garden
I have a Craftsman Gold 6.0 mulching mower with a B&S engine on it that has been idle for about 10 years. It was only lightly used before that and I ran the gas tank dry before putting it away. Today I put gas in the tank pressed the primer bulb 3X and pulled the cord a few times without it starting. I noticed gas dribbling out of the little hole in the center of the primer bulb. It continuously drips and the gas is puddling on the top deck of the mower. Is this likely a problem with the primer bulb or something else? Thanks.
ANSWER : Sounds like the primer bulb dry rotted from sitting &/or the float is stuck in carb. If gas is indeed leaking from bulb. It will need to be replaced. While it is apart, clean carb inside & out with spray carb cleaner.
Read Full Q/A … : Garden
