r pressure
Garden

Experienced gardeners share their insights in answering this question :
Check pressure relief valve. may be set too low, or broken.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The number one cause of low or no pressure when using a pressure washer is a blocked or worn nozzle. Blocked nozzles will prevent water from escaping, while a worn nozzle will allow too much water to pass through, causing the pressure to drop.
The engine of your pressure washer may rev sporadically because it is experiencing an intermittent blockage of the air that it needs to function properly. The first thing that you should do is to check the air filter for clogs caused by debris or dirt. Clean out any clogs that you find and the erratic revving may stop.
Using an old, worn-out nozzle is a common cause of lost pressure, and also has one of the simplest fixes. All you need to do is replace the nozzle and make sure you`re using the proper size. Don`t go by the color of the nozzle, make sure you check the orifice size.
There could be small leaks, holes, or tears in your garden hose or high-pressure hose that are causing your pressure washer to lose pressure when you pull the trigger. If you find leaks, plug the holes or replace the hose, which should solve your pressure issues.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
Surging occurs when the pressure is fine and then weakens. It is caused when the flow rate for the pump cannot be supported by the water supply. Problems can mount from there so it is important that it is dealt with as soon as possible.
Direct drive pressure washer pumps run at around 3400 RPM, while belt-drive pressure washer pumps run at about 1,700 RPM. Because the pump runs at half the speed, it won`t get as hot and, in the long run, will last longer.
If it takes two minutes or less, you`ll be fine, since most pressure washers need 2-1/2 gallon per minute to work. To ensure that water circulates unobstructed through the system, check the water inlet filter or screen and clean it of debris. Also, make sure the garden and pressure hoses are kink free.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

This pressure washer will continue to build pressure when you let off the trigger. I have replaced the hose 3 times because the pump continues to pump until it blows the hose. The pump will not stop pumping!
ANSWER : You have a defective pressure release valve or someone has misadjusted.

Read Full Q/A … : Garden

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

Read Full Q/A … : Garden

Honda powwer boss 3000-whenyoupull the handale to spray it kills the engine
ANSWER : Sounds like the unloader (regulator). Try removing the nozzle, the pull the trigger with the engine running. If motor is still running then it could be the Unloader malfunctioning. If you require a new one try a bypass system for the unloader. The bypass will help save the life of the unloader.

Read Full Q/A … : Garden

Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.
ANSWER : Bad pump

Read Full Q/A … : Garden

My coleman powermate 2750 pressure washer locks the engine up when the trigger is pulled. after a few seconds you can restart it.it comes up to good pressure but kills the motor. Some have told me they thought it was teh pump, but the sprays a little. I would think if the pump was bad it wouldn’t spray at all? Comments?
ANSWER : All i can say is its not a good mechine I owen and repair washers and pumps and use them in line of business thats all i can tell you sorry

Read Full Q/A … : Garden

How do i replace a pull cord on a xt7 pressure washer
ANSWER : Try this link:http://www.youtube.com/watch?v=Q3NjVomUQJMThere are others there as well.Best regards, –W/D–

Read Full Q/A … : Garden

1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
ANSWER : If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.

Read Full Q/A … : Garden

Starts great and sprays great, but will not continue to run when [ stop spraying. It locks up until I release the pressure from the gun.is there a pressure by-pass adjustment I can make?
ANSWER : Tune up motor, replace air filter/spark plug and oil.

Read Full Q/A … : Garden