15″ Electric Factory Reconditioned Trimmer (ZRRY41002) -…

Experienced gardeners share their insights in answering this question :
THE LINE IS WOUND IN BACKWARDS

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The air filter or exhaust port may be blocked. The trimmer may need lubrication and cooling fins or air passages may be blocked. A cordless trimmer`s battery or charger may be faulty.
It is possible that your shaver does not turn on or move because it is dirty. There can be hair or dirt particles stuck inside it, causing the shaving heads to be blocked. To fix this problem, properly clean your shaver. If possible, remove the shaving head and clean your shaver from the inside as well.
When your trimmer starts and runs on choke, it could be because the check valve in the gas cap is clogged. Start the trimmer and gently unscrew the gas cap halfway off. Turn the choke off and assess. If the engine is still running, that means the gas cap may be the culprit.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

It starts and runs for a bit but as soon as it hits thicker grass it dies
ANSWER : Joe Hi there. Sadly your trimmer will struggle on thick grass as it’s not made for it. You could try moving the trimmer like a scythe. This will aid it as your cutting bit by bit.

I need to replace the whole trimmer head and I dont know how to get the gear case off so I can put the new one on. Can anyone help?
ANSWER : To replace the trimmer head you don’t need to replace the gear case. If you look closely about a 1/4 inch up from the safety guard you’ll see a hole in the side of the “gearcase” assemby. (you may have to clean the old dead grass clippings off to see it) You can shove a rod into the hole that will stop the head from spinning freely and I believe you spin the head clock wise (reverse threads) to remove the head.

Can not get spool head apart to change line, tried pump pliers, pipe wrench, won’t unscrew!!
ANSWER : If you are sure that it screws on it may be a reverse threaded unit..

Shaft disengages and trimmer head stops spinning. Seems to be disengaging at coupling were attachments hook up. Shaft slides back and forth and when I turn trimmer off and jiggle trimmer then start it back up it works for a while then stops.
ANSWER : Something wrong with your cintrifical force clutch . it is problably set too loose so the the shaft wont engage

My husqrvarna trimmer head keeps binding up and wont turn. how do i fix this problem?
ANSWER : String wont come out? or head not turning?

How do you load the trimmer head… Lost the user manuel
ANSWER : Check out the manual (available under the technical documents section of the Echo webpage, or at http://www.echo-usa.com/documentation.asp?Model=SRM-210&lang=E )and it will tell you how to change it.

Trimmer head line loading instruction – Husqvarna 28cc Gas Line Trimmer
ANSWER : 1. Remove the cap on the trimmer head, it unscrews.2.
The spool comes off, and on the inside of the spool there is a small
hole, this is where you will start your trimmer line. It it will hold it
in place while you wrap it. There is also arrows on the spool showing
the direction that you need to wrap your spool.3. Insert the
line in the hole and start to wrap the line in the directions of the
arrows, try to keep the line in rows, or else the line may bind and you
will have to do it all over again.4. Feed the line through the
retainer and reinstall the spool by lining up the retainer and the slot
on the outside portion on the trimmer head, the screw back on the
trimmer head and you will be ready to trim.

Why does the echo start but die when i move from cold start to run?
ANSWER : Fuel issue, carb adjustment, fuel lines, carb rebuild.