Push Mower
Experienced gardeners share their insights in answering this question :
If it is running just fine and then suddenly quits it sounds like you have a clogged gas line. it could be a number of things though. If your gas is flowing freely the next thing i would do is clean the carb. Disassemble, blow out all holes with an air compressor and reassemble
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
One of the most common reasons that a lawn mower might stall while it is cutting grass is that it is being overworked. This is a mechanism that is intentionally incorporated into the mower to prevent the motor from being blown.
A Dirty Carburetor Can Cause a Lawnmower To Start Then Die
By far, the most common issue that causes a stalled motor is a dirty carburetor. The carburetor on your engine is the thing that draws in air and mixes it with the fuel. Contrary to what the movies might make you think, gasoline itself is not very flammable.
If your lawn mower starts, runs for a while, then dies, check the ignition coil, gas cap, and spark plug. One or more of these parts could be causing your problem. Follow our repair and symptom guide to help you fix this.
A full gas tank and oil reservoir are the essential first steps when checking why the lawn mower won`t stay running, but the problem could also be a dirty filter, clogged carburetor, improper fuel mixture, or a dirty spark plug.
Your lawn mower runs for 30 minutes then dies if you are having issues such as a bad spark plug, air problems, a malfunctioning carburetor, or a faulty gas cap. You may even encounter the issue that your lawn mower runs for 5 minutes then dies.
Other things that could cause this issue are bad fuel, weak/colapsed/kinked fuel line, faulty spark plug, faulty ignition/coil, oil over full, clogged air filter, plugged/dirty carburetor, worn engine parts internal rings/valves/etc.
Other things that could cause this issue are bad fuel, weak/colapsed/kinked fuel line, faulty spark plug, faulty ignition/coil, oil over full, clogged air filter, plugged/dirty carburetor, worn engine parts internal rings/valves/etc.
If the engine dies when the blades engage, it could be the result of a damaged safety switch. The first step in assessing the safety switch is to make sure it is plugged in securely. The switch is located underneath the seat, and you may have to remove the seat to reach it.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How long does Roundup take to kill weeds – Roundup "" Weed & Grass Killer
ANSWER : 5-7 days
Read Full Q/A … : Push Mower
I have the Gh1000 Grass Hog and when using it, the cutting trimmer line went away. Help!
ANSWER : Replace the line….It is a consumable part. It that your question??
Read Full Q/A … : Push Mower
Uneven grass cutting
ANSWER : I have seen dull blades, blades not installed right and an un-level deck cause that.Hope this helps.
Read Full Q/A … : Push Mower
How to respool the line on grasshog electric grass trimmer
ANSWER : The empty spool can be refilled with 30′ of size .065″ nylon line. Make sure you run the line in the direction of the arrow embossed on the spool.
Read Full Q/A … : Push Mower
42 inch mower cuts uneven, what is the problem?
ANSWER : Several things here could be the problem. Check to see if mower deck is level, measure distance on both side on a level surface. Check tire’s for low air. If you’ve replace the mandrel’s lately, some have a left & right side & if not put back together properly this will cause uneven cutting
Read Full Q/A … : Push Mower
Bad Clutch?? 455 rancher 20″ bar) I have owned it for two years and cut tons of fire wood with it. I recently replaced the oil pump. Yesterday I’m cutting oak like butter. Chain saw is cutting fine.. For no apparent reason it starts struggling to cut. I figure I hit something with the chain. I go to sharpen and notice that the clutch it’s red hot. I take it apart clean it up sharpen it up put it back together fire it up and start to cut. It starts to cut on angle and has no power?? runs fine revving it but will not cut?? What do you think?
ANSWER : Hi Before other checking change the spring of the clutch(2). best regards savumihai71
Read Full Q/A … : Push Mower
Mt999 chainsaw. Brand new. Not cutting through wood although blade rotating. Just seems to be burning wood.
ANSWER : Shouldnt be using a chainsaw if you cant figure the chain is on wrong…….just saying…
Read Full Q/A … : Push Mower
The blades are cutting unevenly – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : I know this will sound a little crazy, but check the air pressure in you tires. My neighbor had the same problem. The tires looked okay until he sat on the mower. One of the rear tires was low which caused the mower to sit lower on one side. Next check the linkages on the deck to make sure they are hooked up and haven’t fell off.
Read Full Q/A … : Push Mower
