Husqvarna
Hydrostatic not engaging
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If all blades are rotating at the same time, there is no issue with the cutting deck belt that is connecting the blades. If one, or more, blades are not rotating, the cutting deck belt is worn out and needs to be replaced. This should be done by an authorised dealer.
Move levers to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times. NOTE: During this procedure there may be some movement of the drive wheels, but they are not under load. The air is being removed from hydraulic drive system.
A Husqvarna riding mower commonly dies when blades are engaged because the grass box is not fully closed. Other possible causes include: Grass Box Misaligned. Grass Box Sensor Wiring Loose.
If the PTO clutch is not receiving power, the clutch solenoid is defective, or the clutch itself is worn out, the blades will not engage. Since a PTO clutch is not repairable, you will need to replace a broken or worn out clutch with a new one.
Failure of any mechanical component, a broken hose, or clogged filter will cause tractor hydrostatic transmission problems. But the most common issue will be the oil itself. In the transmission section of your operator`s manual, you`ll find a section that covers oil viscosity.
They are filled with the specified pump fluid to match each pump design and then sealed by each manufacturer at their factories. Replacing hydrostatic fluid is normally not necessary, unless the drive system is in need of some other internal service or repair.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
A low charge may not provide enough juice to engage the PTO. If you do hear the click, there is power going to it. There could be a problem with safety switches. On most newer model lawn mowers, the brake has to be disengaged or off for the blades to operate.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
MY TRANSMISSION IS VERY WEAK, MOVER WILL SOMETIMES STOP, WONT MOVE, OTHER TIMES IT WILL CREEP ALONG.
ITS ONLY HAS 300 HRS ON IT.
ITS ONLY HAS 300 HRS ON IT.
ANSWER : Noted for frequent failure of hydrostatic transmissions, just search this site. you have to buy another transmission or lawn mower.
Read Full Q/A … : Husqvarna
What information can you tell me about a Husqvarna chainsaw model 61 with serial number 6136460. Does it indicate the year?
ANSWER : Most of the CDI modules have been superseded to part no# 544018401check with your local dealer to verify.
Read Full Q/A … : Husqvarna
Hi, I have a Husqvarna yth2042 rider. We transported it from our house in Michigan to our house in Michigan City, In. It was working just fine when we loaded it and now when we unloaded it the rider won’t move. I disengaged the transmission before we transported it and re-engaged it when we unloaded it but it still won’t move. Any suggestions??
ANSWER : Did the drive belt come off
Read Full Q/A … : Husqvarna
We have a husqvarna cth 170 and we cant seem to reverse it… have any ideas on how?
ANSWER : I have a Husqvarna YTH2348 that clicks when i try to start… I had the battery tested and changed the solenoid and still won’t start. How do I check the starter????
Read Full Q/A … : Husqvarna
Husqvarna 240 want start at all – Husqvarna Chain Saw 18" 450 Model 966955438
ANSWER : Sounds like the ignition module or spark plug. The ignition module is what controls the spark plug that gives your saw the firing capabilities. Before you purchase one of those, replace the spark plug and see if that works. The 240 is a newer husqvarna; so I am skeptical to say it is the ignition module. However, any new product can have a bad part on it. Your saw may have gotten flooded and won’t start. Make sure your gas mixture is 50/50 gas to mixing oil. Always use fresh gas. If you make up gas and don’t use a whole gallon at a time, put some fuel stabilizer in the mixture; so it will still be fresh the next time you use it.
Read Full Q/A … : Husqvarna
Transsmion slipping when going up a small hill
ANSWER : Then you need to get a replacement transmission. Model is stamped on the bottom, do a search on ebay, maybe get lucky as those things are not cheap.
Read Full Q/A … : Husqvarna
Blades will not engage on Husqvarna riding mower.
ANSWER : I have a Husqvarna GTH2548 and the blades will not engage. It is free from all debrie
Read Full Q/A … : Husqvarna
I have a husqvarna riding mower that when i engage the blades the engine stops running
ANSWER : Could be something jamming a blade or belt. With the engine OFF and the key OUT make sure the blades and belts all move freely by hand. Clear out all grass and c**p from the blade and belt areas. You may have to remove the blade deck to do this – instructions are in your manual or download a manual from the Husqvarna website. Good Luck!
Read Full Q/A … : Husqvarna
