Pull cord will not retract, new spring fitted not the problem
Experienced gardeners share their insights in answering this question :
Im not so sure this will help you, except to laugh , let me just say this i hope not, but this one reminded me of one a guy brought to me one day he said it wouldnt start , when i tried to pull it over , it woulnt budge not an inch , after carefull exam of pull rope , i saw the cord had broken and this guy in a fit of frustration used his daughters jump rope to replace it , thats not gonna work , this guy had over six feet of pink jump rope jammed inside this thing , i dont know how he fit it inside but there it was pink and all , i replaced the cord for him (not pink) but did offer to repaint the case pink , he said great maybe i could get my wife to run it then !! long story short maybe the cord reel inside is rubbing on something like a loose bolt or screw they do come loose lots of times ya know
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
What Causes Chain Saw Kickback? There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
T Screw – Next, locate the T screw. This adjustment screw is responsible for adjusting the chainsaws idle. Begin by turning the T screw clockwise until the chainsaw chain begins to move. As soon as you notice it moving, turn the T screw counterclockwise slowly until the chainsaw chain stops.
Kickback, the result of a mechanical fault in a cylinder of an engine which fires before the piston reaches the top. The piston then goes backward while the other pistons in the other cylinders are still going upwards.
If your chainsaw bounces around when making contact with the wood, it means that that chains teeth are not grabbing on and ripping through the wood. A sharp chain will cut in a uniform and straight line.
Recoil starters generally include a pull cord wrapped about a pulley, the pulley being rotated by pulling on the pull cord. The rotational energy generated from the pull cord and pulley is transferred to the drive shaft of the engine through a ratchet and/or clutch mechanism.
The problem may be in the recoil starter itself. A tangled coil of rope or a broken spring may be the problem. In many cases the recoil starter is easily replaced as a single assembly. DO NOT attempt do take the starter apart.
Most quality OEM and replacement recoil springs should be capable of a minimum of 3,000 to 5,000 firing cycles before changing.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Where is the blade oil lines on a 455 rancher
What years did husqvarna make model 61 – Husqvarna Chain Saw 20" Bar
Late 70’s into the early 80’s.
What is correct husqvarna 268 chain file size
For the standard H80 or H81 style chain you will use a 7/32″ (5.5mm) file
What information can you tell me about a Husqvarna chainsaw model 61 with serial number 6136460. Does it indicate the year?
Most of the CDI modules have been superseded to part no# 544018401check with your local dealer to verify.
Kill switch doesn't work, how do i fix it? – Husqvarna 350 18 Inch Gas Chainsaw 52CC Fully Assembled Brand New 18"
The switch connects directly to the coil body of the ignition module. You may have to remove the left side cover to expose the ignition module. The switch, when off, connects this wire to engine ground. There may be debris in the contacts of the switch that prevent contact. You will have to remove the air cleaner assembly and maybe the carburetor itself to access the switch. Good luck!
Saw runs fine for about 15 minutes,then the idle speeds up,then it dies,almost like it is flooding
Do aclean or overhaul of all fuel components.Change the spark plug or the coil aka=spark plug cable.But if your saw in lees the 2 yrs you need to follow the starting guide in order to avoid flooding.If you need more help come back.Post / thumbs / testimonial are welcome!
Where do i find the oil lines on a husqvarna 455 rancher
Husqvarna problems Why won’t the chain spin?
Replace or clean the Drive Clutch.